background image

STEP 5

Connect the boards for your second level in the quantity and orientation as shown below. 

1. 

Connect 

16

x 4ft Boards with Stacking Brackets on 

both ends in alternating orientation.

2. 

Connect 

4

x 2ft Boards with a stacking bracket on

one end and a mid-section 4-way bracket on the 
other end in alternating orientation.

3. 

Connect 

4

x 4ft Boards with a stacking bracket on

one end and a top 4-way bracket on the other end
in alternating orientation.

4. 

Connect 

x 2ft boards with a stacking bracket on one 

end and a mid-section 4-way bracket on the other end in 
the same position.

5. 

Connect 

x 4ft boards with a stacking bracket on 

one end and a top 4-way bracket on the

other end in the same position.

6. 

Connect 

x Curved boards with stacking brackets

on both ends in alternating orientation .

(Bracket all curved boards exactly as shown to the right)

7

. Connect 

x Cut gate Boards with a stacking bracket

on the board end with pre-drilled holes. 

ASSEMBLY INSTRUCTIONS 

Level 1 Continued

Step 2

: Layout the Boards for the first level according to the number of the 

board in Step 1. 

Note:

It is especially important to layout Boards

3

in the exact orientation 

shown in the diagram below.

The gate Board (

Board 1

) on level 1 is kept uncut for 2” profile boards to act as a 

level surface for the gate to swing on. You can choose to cut this Board if you want 
it to be apart of the swinging gate. 

IMPORTANT

: If you connect any brackets incorrectly, they can be removed by 

inserting a flathead screwdriver into the opening of the snap-lock plugs, pushing into 
the nub and twisting upwards.  

Step 3:

When connecting the boards for the first level, insert the stacking 

stakes upside down so the stake is pointing to the sky. This will allow you to 
adjust the shape of your frame before driving the stakes into the ground. 

1

2

Step 4:

Once you finish with the adjustments of your base level frame, flip 

over the stakes and hammer them into the ground. 

1

1

1

1

1

1

1

1

1

1

1

3

3

3

3

2

1

2

2

1

4

4

1

3

2

4

5

6

7

Summary of Contents for Center Circle 16' x 16'






Reviews: