Foxtech XLINK-30 User Manual Download Page 5

XLINK-30 Long Range Video/Data Wireless Transmitting System  

  User Manual

©

2020 FOXTECH All Rights Reserved

  

4

XLINK-30 is a point-to-point data/video wireless transmitting system designed for industrial UAVs, ground 
robots and other data communication applications, featuring 30km long transmission distance.
XLINK-30 integrates the technology of 4G, 5G, WIFI, and adopts OFDM technique and multi-path anti-
interference technology, which has the advantages of long distance transmission, low latency, strong 
diffraction performance, and big data bandwidth communications. 
A great highlight of XLINK-30 is that it supports multi-node interlinked to form a communication mesh, in 
which one node is too far from the ground station to receive signals, it is able to transmit data to its nearest 
node, by which data can be sent back to the ground station.

   1410MHz ~ 1470MHz frequency band 

   2*0.5W transmitting power

   2T2R

   OFDM technology

   Multi-path anti-interference technology

   Latency≤200ms

   Physical layer encryption

   Ethernet and serial control 

   Wireless mesh network transmission

   30km transmission: Unmanned aerial vantenna high-gain panel antenna

   1km~2km transmission: Unmanned ground vomni-directional FRP antenna

Overview

Key Features

Transmission Distance

Summary of Contents for XLINK-30
















Reviews: