- 3 -
- 4 -
Charging Process, Indicate The Battery Level Status
Switch With SemiSolid Battery And LiPo Battery
Storage Mode
If a
SemiSolid
Lithium battery is not used for long time, it's highly recommended to charge or
discharge the
battery to 3.70V with Storage mode so as to extend the battery’s life. when the battery
voltage is higher than 3.70V per cell, the charger will discharge the battery; on the opposite, when the
battery voltage lower than 3.70V per cell, the charger will charge the battery under Storage mode.
1
2
24.00
V
24.00
V
Charging
....
Charging
....
25.0
A
25.0
A
15000mAh
15000mAh
0:38:58
0:38:58
83%
83%
SemiSLi
SemiSLi
1
2
24.00
V
24.00
V
25.0
A
25.0
A
83%
83%
1
2
4
.
00V
4
.
00V
4
.
00V
4
.
00V
4
.
00V
4
.
00V
3
4
5
6
1
2
4
.
00V
4
.
00V
4
.
00V
4
.
00V
4
.
00V
4
.
00V
3
4
5
6
Press the “Mode” button, choose the Storage mode.
Long press the “Start/Stop” button, enter into the Storage mode.
Fault message
Connection Break
Reverse Polarity
Cell Voltage High
INT. TEMP High
Over Load!
No battery connected: check if the battery main port
correctly connected to the device .
Battery polarity reversed: check the battery main port,
polarity connected.
Balance socket voltage abnormality: check if the battery
balance port correctly connected to the device; check the
battery voltage is normal or not.
Temperature protection: check the cooling fan running is
normal or not and check if the external environment
temperature is too high.
Current overload protection: the device will stop charging
once the current over 30A.
Cause analysis
When the charger appear below abnormal situations, the two-color indicators will flash in red, and
LCD display screen will appear fault message, please refer to below specific message notification
and reasons.
Important Warning And Safety Instruction
Warranty And Service
1. Never leave the charger unattended when it is connected to its power supply. If any malfunction
is found, TERMINATE THE PROCESS AT ONCE and refer to the operation manual.
2. Keep the charger away from dust, moist, rain, heat, direct sunshine and vibration.
3. The input voltage is AC 110V or AC 220V, before connect to the power source, please keep its
input voltage is the same as the charger’s.
4. Default battery type is SemiSolid battery type with charge mode. Before connecting the
battery, please keep the battery type comply with the charger setting.
We guarantee this product to be free of manufacturing and assembly defects for a period of one year
from the time of purchase. The warranty only applies to material or operational defects, which are
present at the time of purchase. During that period, we will repair or replace free of service charge
for products deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for
any damage or subsequent damage arising as a result of misuse, modification or as a result of failure
to observe the procedures outlined in this manual.
These warnings and safety instructions are particularly important. Please follow the instructions
for maximum safety. Otherwise the charger and the battery can be damaged or at worst it can
catch fire.
Connection Break
Reverse Polarity
Note: the two-color indicators
will flash in red, and LCD screen
will appear fault message.
www.foxtechfpv.com
TEL: +862227989688
E-MAIL: [email protected]
Foxtech
Important Information Tips
The two-color indicator
will show in red color
The LCD screen will
switch the interface
display every few
seconds, as shown
on the left picture.
Press the
and
simultaneously for 3 seconds
1
1
2
SemiSolid Charge 25A
-.--V
-.--V
-.--V
-.--V
-.--V
-.--V
3
4
5
6
1
1
2
LiPo4.20
Charge 25A
-.--V
-.--V
-.--V
-.--V
-.--V
-.--V
3
4
5
6
