Foxtech NAGA PRO User Manual Download Page 2

Page: 2 / 75

NAGA PRO User Manual

Content

一．

Assembly...............................................................................................

1. Unfold the Arm.....................................................................................

2. Turn on Herelink Remote Controller....................................................

3. Install Battery........................................................................................

4. Install Propeller.....................................................................................

二．

Herelink Remote Controller Introduction..........................................

1. Hardware Update................................................................................

2. Herelink Device Activation................................................................

3. Update Firmware through WiFi..........................................................

4. Pair with the Air Unit..........................................................................

5. Joystick/Rollwheel Calibration and Setting.......................................

6. Power Mode Setting............................................................................

7. Video Sharing......................................................................................

7.1. Enable video streaming on Herelink...............................................

7.2. Share Video via WIFI Hotspot Connection.....................................

7.3. Share videos via USB Connection...................................................

7.4. Share Video via WIFI Connection...................................................

7.5. Display Video Stream......................................................................

8. Connect with Mission Planner Ground Station..................................

9. Watch a Live Herelink Video in Mission Planner..............................

三．

Mission Planner Operation Guide......................................................

Summary of Contents for NAGA PRO












































































Search results

Summary of Contents for NAGA PRO

Reviews:

Related manuals for NAGA PRO

Brands by name

Popular brands

Foxtech NAGA PRO, User Manual

Search results

Summary of Contents for NAGA PRO

Reviews:

Related manuals for NAGA PRO

Brands by name

Popular brands