BARB
CONNECTION
SHU T-OFF
EXTENSION
BARB
CONNECTION
TANK
NOZZLE
PUMP HANDLE
SHU T-OFF
LOCK
ASSEMBLY INSTRUCTIONS
Owner’s Manual
The Fountainhead Group
Compressed Air Sprayer
1-800-3 11-9903
Owner’s Manual
OMLB-2, OMLP-2, RMLB-2, RMLP-2
WARNING!
The sprayer is operated with liquid under pressure. Failure to observe CAUTION and to follow instructions for operating and cleaning
can cause tank, hose and other parts to be weakened and/or rupture under pressure. This can result in SERIOUS INJURY from high pressure discharge of liquids
or forcible ejection of parts. DO NOT USE FLAMMABLE MATERIALS IN THIS SPRAYER. Material could ignite or explode, causing serious injury. FOR SAFE USE
OF THIS PRODUCT - YOU MUST READ AND FOLLOW ALL INSTRUCTIONS BEFORE USE.
TEST SPRAYER WITH WATER BEFORE USING ANY CHEMICALS .
SAFETY PRECAUTIONS:
1. Read owner’s manual completely before
operating this sprayer.
2. This sprayer is designed for light duty lawn and
garden use only.
3. Always use goggles, gloves and protective
clothing when using spraye r.
4. Read and follow all instructions and cautions on
label of products used in this sprayer.
5. Spray when air is calm to prevent drift of
chemical.
6. Do not leave sprayer in the sun when not in
use.
7. Never use flammable liquids, caustics, acids
or hot water in this tank.
8. Never store chemicals in this tank.
9. Always release pressure when sprayer is not in
use and before removing pump from tank.
10. Never stand with face or body over sprayer when
pressurizing tank or releasing pressure.
11. Clean and rinse sprayer thoroughly after each use.
12. Never attempt to alter sprayer from original
condition.
13. Always use replacement parts from original
manufacture r.
1-800-3 11-9903
If you have any problems with, or have any questions about your spraye
r, BEFORE YOU
RETURN IT TO THE STORE, CALL OUR TOLL FREE CUSTOMER SERVICE CENTER AT:
HOSE ASSEMB LY INSTRUCTIONS
11
22
11
1. PUSH HOSE COMPLETELY ON.
2. TIGHTEN NUT COMPLETEL Y.
!
!
NEVER USE SPRAYER WITHOUT NU T.
1 .
2 .
1 .
2 .
3 .
HOSE ASSEMBL Y TO TANK:
IMPORT ANT :
A
hose nut
is included in the parts
kit. The hose nut is
required
for
proper assembly
of the sprayer.
Do not
attempt to
heat,
or
alter
hose, hose nut, or barb prior to assembly.
Slide hose nut over end of hose (observe
proper hose nut orientation in above
diagram). Push hose completely onto tank
barb, as shown in step #1 of above diagram.
Slide hose nut along hose and over barb
threads.
Turn hose nut clockwise to
completely tighten over hose, as shown in
step #2 of above diagram (do not use tools).
Remove protective cap from end of shut-off
assembl y.
Screw extension onto end of shut-off
assembly until firmly attached.
Select a nozzle, using NOZZLE SELECTION
CHAR T. Screw selected nozzle onto
extension until firmly attached,
making sure
#171092 (o-ring) is in place on end of
e x t e n s i o n .
When using flat fan nozzles, make sure tabs
on nozzle tips are fitted into slots on end of
extension. Tip can be installed to produce a
vertical or horizontal flat fan.
4 .
EXTENSION ASSEMBL Y TO SHUT-OFF
E-mail: [email protected] • Web site: ww w.TheFountainheadGroup.com • 1-800-3
11-9903
FILTER
CLEANING
(
(See SPRAYER
MAINTENANCE PAGE 2)
OPER ATING
INSTRUCTIONS
F I L L I N G
1 .
2 .
Remove pump by turning pump handle
counterclockwise.
Fill tank to desired level (always refer to
chemical manufacturer for proper mixture)
Place pump into tank opening and turn handle
clockwise to tighten.
3 .
Make sure shut-off lock is not engaged (if
shut-off lock is engaged while pressurizing,
the unit will immediately start spraying)
Pressurize sprayer by pumping handle in a
smooth up and down motion. When desired
pressure is achieved, lock handle onto pump.
P R E S S U R I Z I N G
Point nozzle away from you. Press shut-off
button to begin spraying. Release button to
stop spraying. When using adjustable nozzle,
adjust spray pattern by turning nozzle tip.
(Note: Flat fan nozzle is not adjustable).
For continuous spraying, squeeze shut-off
handle and rotate lock toward the sprayer tip.
1 .
2 .
S P R A Y I N G
1 .
2 .
Direct nozzle away from you and press
handle on shut-off until unit stops spraying
(this will release pressure in tank).
Turn pump handle counterclockwise to
remove pump.
Empty any remaining liquid according to
product disposal directions. Clean sprayer as
directed under
CLEANING SPRAYER
.
F I N I S H I N G
1 .
2 .
PN 180568 2003
3 .
ALWAYS ENSURE PRESSURE IS RELEASED
FROM TANK BEFORE FILLING OR SERVICING.
Squeeze shut-off handle and hold down until
the unit stops spraying. Then, and only then, it
is safe to remove pump.
I M P O R T A N T !
Filter
Hose Assembly
Shut-Off
A s s e m b l y
