50
Mixer Functions (VF80EX)
Effect parameter details
The parameters that can be adjusted will depend on the parameter type.
The following describes parameters for effect types L01 through L38 used for the loop effect.
See "Advanced Operations" on page 84 for details about parameters for effect types L39 through L44 used for
the insert effect.
Reverb effect parameters (parameter type: REVERB)
For effect types
1--24
of the preceding "Effect type" table, the following five parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Rev Time
Adjust the length of reverberation. Range:
0.1--9.9 seconds
3.
Pre Delay
Adjust the time from the original sound until reverberation begins. Range:
0--100 ms
4.
Hi Ratio
Adjust the decay ratio of the high frequencies. Range:
0--10
5.
E/R Level
Adjust the volume of the early reflections. Range:
0--99
Delay+reverb effect parameters (parameter type: DELAY+REVERB)
For effect types
25--28
of the preceding "Effect type" table, the following five parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Delay Time
Adjust the delay time: Range:
1--230 ms
3.
Feedback
Adjust the number of delay repeats. Range:
0--99
4.
Delay Bal
Adjust the delay balance. Range:
0--99
5.
Rev Time
Adjust the length of reverberation. Range:
0.1--9.9 seconds
Delay effect parameters (parameter type: DELAY)
For effect types
29
and
30
of the preceding "Effect type" table, the following five parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Delay Time
Adjust the delay time. Range:
1--680 ms
3.
Feedback
Adjust the number of delay repeats. Range:
0--99
4.
Hi Ratio
Adjust the decay ratio of the high frequencies. Range:
0--10
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
BPM delay effect parameters (parameter type: BPM DELAY)
For effect types
31
and
32
of the preceding "Effect type" table, the following five parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
BPM
Adjust the BPM. Range:
30--250 bpm
If the delay time exceeds 680 ms, "!" is shown.
3.
Note
Select the note value for the delay. Range:
24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
*
24
= 16th note sextuplets,
16
= 16th notes,
8T
= 8th note triplets,
16.
= dotted sixteenth notes,
8
= 8th notes,
4T
= quarter note triplets,
8.
= dotted eighth notes,
4
= quarter notes,
2T
= half-note triplets,
4.
= dotted quarter notes,
2
= half notes
* The "
.
" shown in the ninth character of the LCD indicates a dotted note.
* The "
T
" shown in the ninth character of the LCD indicates a triplet.
4.
Feedback
Adjust the number of delay repeats. Range:
0--99
(100 steps in increments of 1)
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Short delay effect parameters (parameter type: SHORT DELAY)
For effect type
33
of the preceding "Effect type" table, the following five parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Delay Time
Adjust the delay time. Range:
0.1--9.9 ms
,
10--99 ms
,
100--200 ms
3.
Feedback
Adjust the number of delay repeats. Range:
0--99
4.
Hi Ratio
Adjust the decay ratio of the high frequencies. Range:
0--10
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Doubling effect parameters (parameter type: DOUBLING)
For effect type
34
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Lch Delay
Adjust the delay time of the L channel. Range:
0.1--9.9 ms
,
10--99 ms
,
100--200 ms
3.
Rch Delay
Adjust the delay time of the R channel. Range:
0.1--9.9 ms
,
10--99ms
,
100--200 ms
4.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
