Model PH-100
Rear Panel section
8. [INPUT (-10dBV)] jacks (L, R)
(PHONE: -10dBV)
Connect to -10 dBV balanced output connectors of
an external device.
A stereo signal from these balanced connectors are
sent
[PHONES]
jacks (1 through 10) on front and
rear panel.
You can control the signal levels using the
[INPUT]
control on the front panel.
3. [CASCADE OUT] jacks (L, R)
(RCA: -10dBV)
To cascade two PH-100s, connect between the
cascade jacks of the first unit and the unbalanced
[INPUT]
jacks of the second unit.
See page 6 for details about cascade connection.
+4dBu
5
4
3
2
1
10
9
8
7
6
PHONES (PRIORITY TO "FRONT PHONES" OUTPUT)
AC IN
CASCADE
OUT (-10dBV)
L
10
9
8
7
6
R
L/MONO
INPUT
(-10dBV)
CHANNEL IN (-10dBV)
INPUT L
INPUT R
-10dBV
-10dBV
HOT
R
L/MONO
AUX IN
(-10dBV)
COLD
GND
XLR
PHONE
2
3
1
T
R
S
2
1
4
3
5
R
+4dBu
1
2
3
4
5
6
7
8
1. [AC IN] connector
Connects the supplied power cord.
6. [INPUT (-10dBV)] jacks (L/MONO, R)
(RCA: -10dBV)
Connect to -10 dBV unbalanced output connectors
of an external device.
A stereo signal from these jacks is sent the
[PHONES]
jacks (1 through 10) on front and rear panel.
If you connect a plug only to the “L/MONO” jack,
the same signal is sent to both L and R channels.
4. [CHANNEL IN] jacks (1 through 10)
(RCA: -10dBV)
The signal from each input jack is directly sent to
the corresponding headphone output.
i.e. The signal from
[CHANNEL IN 5]
is directly
output from
[PHONES 5]
.
5. [AUX IN] jacks (L/MONO, R)
(RCA: -10dBV)
Connect to -10 dBV unbalanced output connectors
of an external device.
A stereo signal from these input jacks is sent the
[PHONES]
jacks (1 through 10) on front and rear
panel. If you connect a plug only to the L/MONO
jack, the same signal is sent to both L and R
channels.
You can control the signal level using the
[AUX IN]
control on the front panel.
7. [INPUT (+4dBu)] connector (L, R)
(XLR-3-31 type: +4dBu)
Connect to +4 dBu balanced output connectors of
an external device.
A stereo signal from these balanced connectors are
sent
[PHONES]
jacks (1 through 10) on front and
rear panel.
You can control the signal level using the
[INPUT]
control on the front panel.
1
3
2
The pin assignment of the XLR connector
The pin assignment of the phone plug
Sleeve
Ring
Tip
1
2
3
GND
HOT
COLD
Sleeve
Tip
Ring
GND
HOT
COLD
2. [PHONES] jacks (1 through 10)
Connect headphones. There are also headphone
jacks on the front panel so you can use whichever
you like.
<Note>
Each headphone jack on the front panel take prior-
ity to the corresponding (same number's) head-
phone jack on the rear panel.
You cannot use both front and rear jacks with the
same number simultaneously. If you connect head-
phones to both front and rear jacks with the same
number, you can only use the headphones connected
to the front jack.
4
You can control the signal level using the
[INPUT]
control on the front panel.
To cascade two PH-100s, connect between the
[CASCADE OUT]
jacks of the first unit and the
unbalanced
[INPUT]
jacks of the second unit.
See page 6 for details about cascade connection.
