fos4X Blackbird OECD Instructions For Use Manual Download Page 40

Page: 40 / 83

3. Product Description

Firmware Update

Figure 23: Firmware Update

The page FIRMWARE UPDATE displays the following information:

■

Current Firmware Version

: Currently installed firmware version.

In the section

Firmware Update

the firmware of the Blackbird OECD can be

updated. See

Firmware Update via Web Interface, page 73

3.5.3 Signal Quality

The values for the signal quality have the following meanings:

■

Signal Good

: Signal quality is good. Measurements are possible without

restrictions.

■

Signal Warning

: There are one or more warnings. See

Tab. 32: Signal Quality,

page 40

. Measurements are possible. The measurements may be inaccurate

due to boundary effects and environmental conditions.

■

Signal Problem

: There are one or more errors. See

Tab. 32: Signal Quality,

page 40

. Measurements are not possible.

Table 32: Signal Quality

Signal Quality

Associated status codes

Signal Good

40 / 83

MDE1261_4-10_1.3.x_5.0_Blackbird

OECD_(12CH, CNO)-en-us

Summary of Contents for Blackbird OECD




















































































Search results

Summary of Contents for Blackbird OECD

Reviews:

Brands by name

Popular brands

fos4X Blackbird OECD, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD

Reviews:

Brands by name

Popular brands