![FortrezZ WWA-01 Instruction Manual Download Page 2](http://html.mh-extra.com/html/fortrezz/wwa-01/wwa-01_instruction-manual_2322523002.webp)
1080 Centre Rd. Suite C
Auburn Hills, MI 48326
www.fortrezz.com
Phone: (248) 481-7092
Made in USA
network). Depending on your Z-Wave controller, it is possible to receive a remote alert. For example, with some gateway controllers,
you can receive an email or cell phone text message when an alarm is activated. With a gateway’s remote access and depending on
your specific controller’s capabilities you will be able to check the status of any WWA-01 in your network.
Choosing a mounting location
The WWA-01 is suitable for use in dry, interior locations only. Avoid placing the WWA-01 close to a metal frame, or other metal
enclosures that may affect RF range. Also, avoid areas with rapid temperature swings. Place the unit so that any leaks that may occur
will not drip directly on the unit.
Recommended WWA-01 uses: Under sink, Next to Sump pumps, Water Heaters, Laundry Room, Bathroom Floor, Storage Area,
Garage, Utility Sink, Vacation/Recreation homes, Boats etc.
Low Battery
The WWA-01 will broadcast an alert on the Z-Wave network at regular intervals when it detects a low battery condition. In addition, it
will periodically sound an audible ‘chirp’. Your controller may be able to be configured to monitor the WWA-01 wake up notifications. If
these stop, then this might be an indication that the battery has died or that transmissions from the WWA-01 are no longer be received.
Because the audible water alarm draws a large current from the battery, the battery should be replaced each time an actual water leak
has been detected. After a water leak, please ensure that there is no moisture in the unit before replacing the battery. Do not install
batteries that appear damaged or unsealed. When replacing batteries, the water seal may be broken around the screws. After
screwing the parts back together, it is recommended to use some sealant such as silicone caulk around the screws.
FCC Compliance Statement Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired operation.
FCC Warning (Part 15.21).
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Interference Statement (Part 15.105 (b))
. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement per Section 4.0 of RSP-100
.
The term "
IC:
" before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
Section 7.1.5 of RSS-GEN.
Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must
accept any interference received, including interference that may cause undesired operation.
Limited Warranty:
THE PRODUCT IS PROVIDED WITH ONE YEAR LIMITED MANUFACTURER WARRANTY. FORTREZZ,
LLC warrants its products to be free from defects in material and workmanship under normal use for one year,
and is not responsible for consequential damages or installation costs of any nature. FORTREZZ, LLC.
expressly disclaims all implied warranties, including but not limited to the implied warranties of merchantability
and fitness for a particular purpose. FORTREZZ, LLC. does not warrant, guarantee, or make any
representations regarding the use or the results of the use of the products or any accompanying materials in
terms of their correctness, accuracy, reliability or otherwise. In no event shall FORTREZZ, LLC. be liable to
Purchaser hereunder or in respect of any products ordered or delivered to Purchaser, whether in contract, tort
including negligence or otherwise for a loss of profits or loss of use or for any incidental, consequential, special
or indirect damages howsoever caused whether or not FORTREZZ, LLC. has been advised of the possibility of
such loss or damage. FORTREZZ, LLC's maximum liability to Purchaser under these conditions shall in no
event exceed the amount paid by Purchaser for the products that are the subject of the claim and in respect of
all claims for products ordered from FORTREZZ, LLC. to which these conditions apply to the amount paid by
Purchaser for the products which are the subject of the claims. If you are not comfortable with your limited
warranty, or not completely satisfied with the WWA-01, or the WWA-01 does not perform as expected we
encourage you to return the WWA-01 to your DISTRIBUTOR for an exchange or for a full refund within 30
days of purchase. Or, you can return the WWA-01 to FORTREZZ with an RGA number.
All products to be returned to FORTREZZ, LLC. must have a valid Returned Goods Authorization (RGA).
Send the returned unit to:
FortrezZ, LLC Warranty Replacement, 1080 Centre Rd. Ste C. Auburn Hills, MI 48326,
postage prepaid
with a payment of US$ 9.95 to cover the cost of return shipping, postage and handling. You must use the original packaging and
include a proof of purchase (photocopy of receipt) along with the RGA # and the returned Wireless Water and Freeze Alarm.