manualshive.com logo in svg

Fortinet FortiGate FortiGate-300A, Administration Manual, Page: 27 / 392

Share
Download
Fortinet FortiGate FortiGate-300A Administration Manual Download Page 27

System status 

Status

FortiGate-300A Administration Guide

01-28006-0092-20041105

 27

System status

Unit Information

Admin users and administrators whose access profiles contain system configuration 
read and write privileges can change or update the unit information. For information 
on access profiles, see 

“Access profiles” on page 113

.

Recent Virus Detections

Interface Status

All interfaces in the FortiGate unit are listed in the table.

UP Time

The time in days, hours, and minutes since the FortiGate unit was last 

started.

System Time

The current time according to the FortiGate unit internal clock. 

Log Disk

Displays hard disk capacity and free space if the FortiGate unit contains a 

hard disk or Not Available if no hard disk is installed. The FortiGate unit uses 

the hard disk to store log messages and quarantine files infected with a virus 

or blocked by antivirus file blocking. 

Notification

Contains reminders such as “Change Password” or “Product Registration”. 

Select the reminder to see the detailed reminder message.

Host Name

The host name of the current FortiGate unit.

Firmware Version

The version of the firmware installed on the current FortiGate unit.

Antivirus Definitions

The current installed version of the FortiGate Antivirus Definitions.

Attack Definitions

The current installed version of the FortiGate Attack Definitions used by 

the Intrusion Prevention System (IPS).

Serial Number

The serial number of the current FortiGate unit. 

The serial number is 

specific to the FortiGate unit and does not change with firmware 

upgrades.

Operation Mode

The operation mode of the current FortiGate unit.

Time

The time at which the recent virus was detected.

Src / Dst

The source and destination addresses of the virus.

Service

The service from which the virus was delivered; HTTP, FTP, IMAP, 

POP3, or SMTP.

Virus Detected

The name of the virus detected.

Interface

The name of the interface.

IP / Netmask

The IP address and netmask of the interface (NAT/Route mode only).

Status

The status of the interface; either up (green up arrow) or down (red 

down arrow).

Summary of Contents for FortiGate FortiGate-300A









































































































































































































































































































































































































Reviews:

No comments