ALL-IN-ONE DATA INTERFACE
REMOTE STARTER / ALARM
QUICK
INSTALLATION GUIDE
Manual
transmission only
supported on
vehicles with door
trigger available
on the CAN
network.
READY MODE
TO DISABLE READY MODE
COLD START MODE
WARNING
REMOTE START / ALARM DIAGNOSTICS
Make sure that
all doors are
closed and the
transmission is
in the NEUTRAL
position.
While the
engine is
running.
Engage the
parking
brake.
Release the
brake pedal.
STANDARD
• Open any door(s)
• Open the hood
Note :
If the Parking lights flash 3 times when Remote-Starting, Ready
Mode is not enabled.
• Disengage the parking brake
Remove the
key from the
ignition barrel.
The vehicle
will remain
running with the
Remote-Starter.
Exit the vehicle
and close all of the
doors.The Remote-
Starter will stop
running once all the
doors are closed.
REMOTE STARTER DIAGNOSTICS
Parking lights flashes (before starting) :
3x
Ready Mode disabled
4x
Valet Mode activated (The LED is on)
5x
Hood open
Parking lights flashes (after starting) :
1x
Normal stop (Brake, Park Brake)
3x
Runtime expired or shut down by Transmitter
4x
No tachometer signal
5x
Hood open
6x
Over crank threshold (8 seconds)
ALARM DIAGNOSTICS
Parking lights flashes (after disarm) :
3x
Door open – zone 3
4x
Shock sensor – zone 4
5x
Hood open – zone 5
6x
Trunk open – zone 6
7x
Auxiliary IN– zone 7
Note. : x Indicates the number of times the parking lights will flash.
+
TO ENABLE
Press and release the FUNCTION button, within 12
seconds simultaneously press and and hold the LOCK and
START buttons for 1 second. The remote’s Green LED will
flash and beep once to confirm. The parking lights will
flash once.
TO DISABLE
• Press and release the FUNCTION button, within 12 seconds
simultaneously press and and hold the LOCK and START buttons for 1
second. The remote’s Green LED will flash and beep once to confirm. The
parking lights will flash twice.
• Put the Remote-Starter/alarm into Valet
• Remote-Start the vehicle
• Open the hood
• Press the brake pedal
• Turn the key to the ignition position.
• Disable Ready Mode (manual transmission).
Push the START button
(3 seconds).
The Parking lights will
flash once and then
remain on.
DISARM / ENTER / EXIT VALET MODE
STEP 1
STEP 2
to disarm
the system
FMH
2-W
System
armed :
DEL flash
Insert the
key and
turn it to
the ignition
(ON/RUN)
position.
OR
Within 10
seconds
press and
release
the Valet
switch
or the
antenna
button 3
times.
FMH
2-W
System dis-
armed :
LED is OFF
3x
3x
FMH
2-W
to enter and
exit valet
mode
FMH
2-W
System
disarmed :
LED is OFF
FMH
2-W
System dis-
armed and in
valet mode :
LED is ON.
EVO-ONE
EVO-ONE
ONE
ONE
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either
damage to the vehicle itself or to the remote-starter module. This module must be installed by a certified technician including all of the
supplied safety devices. Please note that this guide has been written for trained professional technicians, a certain level of skills and knowledge
is therefore assumed. Please review the Installation Guide carefully before beginning any work.
By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the
main unit must be cut. Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle
is in the “drive” or “reverse” position. If an automatic transmission vehicle starts when the transmission is in gear, ensure that the safety wire
loop on the unit is not cut. Once the safety wire loop is cut, the system is considered an automatic transmission remote-starter indefinitely.
Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual transmission vehicle.Neither the
manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the
replacement of this module in case of manufacturing defects.
This module must be install by qualified technician. This instruction guide may
change without notice. To download the installation guide, user guide, or the latest quick installation guide, visit: www.fortin.ca
Technical support:
TEL: 514-255-4357
1-877-336-7797
www.fortin.ca
RF441W
