ALL-IN-ONE DATA INTERFACE
REMOTE STARTER / ALARM
QUICK
INSTALLATION GUIDE
Manual
transmission only
supported on
vehicles with door
trigger available
on the CAN
network.
READY MODE
TO DISABLE READY MODE
ENTER/EXIT VALET MODE
COLD START MODE
WARNING
REMOTE START / ALARM DIAGNOSTICS
Make sure that
all doors are
closed and the
transmission is
in the NEUTRAL
position.
Insert the key and turn it to the ignition (ON/RUN)
position.
Within 10 seconds press and release the Valet
switch 3 times.
While the
engine is
running.
Engage the
parking
brake.
Release the
brake pedal.
Push the START button
(3sec.).
The parking lights will
fl ash once and then
remain on.
STANDARD
• Open any door(s)
• Open the hood
• Disengage the parking brake
Note :
If the parking lights fl ash 3 times when Remote-
Starting, Ready Mode is not enabled.
Remove the
key from the
ignition barrel.
The vehicle
will remain
running with the
Remote-Starter.
Exit the vehicle
and close all of the
doors.The Remote-
Starter will stop
running once all the
doors are closed.
REMOTE STARTER DIAGNOSTICS
Parking Light fl ashes (before starting) :
3x
Ready Mode disabled
4x
Valet Mode activated (The LED is on)
5x
Hood open
Parking Light fl ashes (after starting) :
1x
Normal stop (Brake, Park Brake)
3x
Runtime expired or shut down by Transmitter
4x
No tachometer signal
5x
Hood open
6x
Over crank threshold (8 seconds)
ALARM DIAGNOSTICS
Parking Light fl ashes (after disarm) :
3x
Door open – zone 3
4x
Shock sensor – zone 4
5x
Hood open – zone 5
6x
Trunk open – zone 6
7x
Auxiliary IN– zone 7
8x
Tilt Sensor – zone 8
9x
Ignition – zone 9
Press simultaneously LOCK and STOP buttons for 1
second until the parking lights fl ash once.
TO DISABLE
• Press simultaneously LOCK and STOP buttons for 1 second until the
parking lights fl ash twice.
• Put the Remote-Starter/alarm into Valet
• Remote-Start the vehicle
• Open the hood
• Press the brake pedal
• Turn the key to the ignition position.
• Disable Ready Mode (manual transmission).
-C
EVO-ONE
EVO-ONE
ATX5
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either
damage to the vehicle itself or to the remote-starter module. This module must be installed by a certifi ed technician including all of the
supplied safety devices. Please note that this guide has been written for trained professional technicians, a certain level of skills and knowledge
is therefore assumed. Please review the Installation Guide carefully before beginning any work.
By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the
main unit must be cut. Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle
is in the “drive” or “reverse” position. If an automatic transmission vehicle starts when the transmission is in gear, ensure that the safety wire
loop on the unit is not cut. Once the safety wire loop is cut, the system is considered an automatic transmission remote-starter indefi nitely.
Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on a manual transmission vehicle.Neither the
manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the
replacement of this module in case of manufacturing defects.
This module must be install by qualifi ed technician. This instruction guide may
change without notice. To download the installation guide, user guide, or the latest quick installation guide, visit: www.fortin.ca
Technical support:
TEL: 514-255-4357
1-877-336-7797
www.fortin.ca