manualshive.com logo in svg

Forster Products Co-Ax, User Instructions, Page: 6 / 8

Share
Download
Forster Products Co-Ax User Instructions Download Page 6

 

6 

7.2 

Adjust the Co-Ax Press 

 

7.21 

Primer Seater Assembly (See Figure 7.) 

Based on the primer diameter being used, select either the 

Small Primer Seater Assembly or the Large Primer Seater 

Assembly (see Figure 7) and screw it into the Co-Ax Press.  
 

Figure 7. Primer Seater Assembly Versions 

Small Primer Seater 

Assembly 

(-101) 

 

.175" 

Diameter

 

Large Primer Seater 

Assembly 

(-102) 

 

.210" 

Diameter

 

 

7.22 

Top Shell Holder Jaws (See Figure 8.)

 

Based on the thickness of the case rim being used, ensure 
all three ends of the Top Shell Holder Jaws are matched and 
aligned, and held loosely face down on the Shell Holder Jaw 
Block (-017). Note the stamped circle that indicates which 
ends are aligned. 
 

Figure 8. Top Shell Holder Jaws (-016) 

0.054” Ends 

 

0.072” Ends 

 

.054"

.072"

Stamped 

Circle

 

Top Shell Holder Jaws in Place and Ready to Be 

Tightened 

 

7.23 

Locator

 

1.  Match the Locator end to the primer diameter being 

used. (See Figure 9.)  

 

Figure 9. Locator (-018) 

.175" Diameter

.210" Diameter

 

 
2.  Lower the Co-Ax Press Handle until there is enough 

room to insert the Locator up into the Top Shell Holder 
Jaw Block (-017) from underneath. 

3.  Center an unprimed case on the Locator. 
4.  While holding the locator in place, adjust the three Top 

Shell Holder Jaws inward onto the case rim and tighten 
the three Socket Head Cap Screws (SCR10-
24X1/2SHEADCAP) around the case. Do not 
overtighten. (See Figure 10.) 

 

Figure 10. Locator in Use 

 

 
5.  Lower the Co-Ax Press handle and remove the Locator. 

You are now ready to prime. If the case rim is either too 
loose or too tight, try using the opposite end of the Top 
Shell Holder Jaws. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Co-Ax









Reviews:

No comments