Set-up Guidelines
1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 115V. If the outlet is shared
with another electronic device, the total current should not exceed 30A (at 115V).
Specifications
Paper
Optical Media
Cutting Style:
Cross Cut
Cross Cut
Shred Size:
1mm x 5mm
2mm x 2mm
Sheet Capacity:
10 - 11 sheets (75gsm)*
1 disc at a time
Speed:
Up to 18 fpm
Approx. 800 discs/hour
Feed Opening
9.4”
4.9”
Bin Capacity
28 gal.
21 gal.
DIN 66399 Security Level
P-7
O-6
Dimensions:
31” W x 26” D x 45” H (800 x 650 x 1135mm)
Weight:
530 lbs. (240kg)
Power Supply:
115V, 60 Hz
*Capacity varies depending on paper and power supply
AutoOiler
The AutoOiler pumps 40 CCs of oil onto the paper cutting head
every 30 minutes of run time to help keep the FD 8732HS working
at peak performance.
1. Fill oil reservoir with recommended HS shredder oil.
2. Insert hose into the top of the bottle.
3. The oiler is ready for use.
CAUTION!
Not for use with staples or paper clips they will damage the cutting blades.
Oil reservoir bottle
Hose & cap
assembly
Operation
1. Flip the power switch “ON” located on the right side of the shredder.
2.
Auto Start/Auto Stop
When the START button is pushed, the “AUTO” LED will light.
Insert paper/optical media to shred. The shredder will start and stop
automatically when using this function. For optical media, feed discs
one at a time.
3.
Manual Operation
If the paper or optical media is too small for the shredder’s sensors to
detect, shred it manually. Push the START button once more and the
“MANUAL” LED will light. Insert paper/optical media to be shredded.
Three minutes after shredding, the cutter automatically stops rotating.
4.
Reverse Operation
Push the REV button and the “REV” LED will light and cutting blades
will operate in reverse. If too much paper/optical media is inserted at
one time in standard modes, the shredder will automatically operate
in reverse. If this occurs, remove the inserted paper/optical media and
shred in smaller amounts. NOTE: The maximum amount of paper to
be shredded differs according to paper quality, humidity and voltage. If the shredder is to
be used continuously, do not insert more than half of the maximum capacity.
5.
Full Sensor
If the wastebasket is full, the “FULL” LED will light and the cutter will stop automatically.
Open the door, remove and empty the waste bin. Replace the waste bin, close door, and
press START to resume shredding.
Safety Precautions
To avoid personal injury, and damage to the shredder,
observe the following safety precautions. Please keep these
instructions for future reference.
NOTE:
In case of emergency, flip the “Power Switch”
to cut off power and/or pull the plug out of the wall outlet.
Power switch
•
Keep hands, long hair, clothing, ties, jewelry and loose
items away from the feed openings and shred outlet.
•
Do not use the shredder for anything other than its intended purpose. Never use the
paper shredding infeed to shred cloth, plastic, cardboard or any hard material that will
cause damage to the shredder blades. Feed only discs into the optical media slot.
•
Do not allow children to use the machine.
•
Do not operate with a damaged power cord or plug, or when the machine is damaged
in any manner.
•
Unplug the shredder when it is being moved, or if it is not in use for an extended
period of time.
continued on the next page
ECO Mode
When the power switch on the right side of the shredder (see below) is initially turned on,
the shredder is automatically in ECO Mode. This energy-saving feature puts the shredder
into standby after 5 minutes of inactivity.
When the shredder is in standby, the ECO Mode LED on the control
panel will be lit. Simply press the start button to begin shredding.
To turn off ECO Mode: Turn the power switch to the off position, then while pressing
the stop button turn the shredder back on, hold the stop button down until the shredder
beeps once and release. The Eco Mode indicator LED will go out indicating that the
shredder is no longer in Eco Mode. To re-engage Eco Mode simply turn the shredder off
and back on again.
CAUTION:
To avoid damage, DO NOT manually
apply oil to the optical media cutting head.
