Made in China.
16 - 24 in.
(406 - 610 mm)
16 - 24 in.
(406 - 610 mm)
3-1
3-2
3-3
3-4
6901-006004
Assemble
the wall plate
sections
01
and
02
with the
connection plate
screws
03
.
Drill pilot holes using a 1/8 in. (3 mm) diameter drill bit.
IMPORTANT
: Be sure to drill into the center of the stud.
IMPORTANT
: Pilot holes must be drilled to a depth of 3 in. (75 mm).
09
10
01
02
Locate your
stud. Verify
and mark
the center
of the stud
by
fi
nding the
stud edges using
an awl, a thin
nail, or an edge-
to-edge stud
fi
nder.
Position
the wall
plate
assembly
at your desired
height and line
up the holes with
your stud center
line. Level the wall plate
and mark the holes.
01
02
Install the
wall plate
assembly using lag
bolts
09
and washers
10
. Tighten
the lag bolts
09
only until
the washers
10
are pulled firmly against the
wall plate assembly.
Step 3 Attach Wall Plate ( Wood Stud installation)
Step 2 Assemble Wall Plate
3 in. (75 mm)
1/8 in.
(3 mm)
01
02
03
CAUTION:
Avoid potential personal injuries and property damage!
●
Drywall covering the wall must not exceed 5/8 in. (16 mm)
●
Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1
½
x 3
½
in. (38 x 89 mm)
CAUTION:
Avoid potential personal injury or property damage! All lag bolts
09
MUST BE firmly tightened to prevent
unwanted movement of the wall plate assembly.
CAUTION:
Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.
S
CAUTION:
Avoid potential personal injuries and
property damage!
●
Minimum solid concrete thickness: 8 in. (203 mm).
●
Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
●
Minimum horizontal space between fasteners: 16 in (406 mm
).
●
Mount wall plate
10
directly onto the concrete surface.
STEP 4
Wall Plate Install ( Solid Concrete or Concrete Block )
Min.
8 in.
(203 mm)
Min. 8 in.
(203 mm)
Min. 16 in.
(406 mm)
s
01
HEAVY! You may need
assistance with this step.
IMPORTANT:
You will hear an audible click when the TV
brackets
04
and
05
are
securely fastened to the wall plate
Hook TV brackets
04
and
05
onto wall plate
10
02
01
10
01
02
10
01
02
02
01
10
STEP 5: Attach TV to Wall Plate
1
2
Loosen the knob on
TV brackets
04
and
05
to adjust the tilt of your TV. Tighten the knob
when your TV is set to the desired tilt.
Pull down on the straps on
TV brackets
04
and
05
and lift the TV up and out away from the wall plate
REMOVING THE TV
Slowly slide the TV along wall plate
LATERAL SHIFT
Adjustments
TILT
05
04
02
05
04
or
01
02
01
Position wall plate
01
at your
desired height. Level, then
mark the four hole locations.
Drill four pilot holes using a 3/8 in.
(10 mm) masonry drill bit.
IMPORTANT:
Pilot holes must be
drilled to a depth of 3 in (75 mm)
.
Never drill into the mortar between blocks.
Insert four concrete anchors
( 10x50mm) to the wall
CAUTION:
Be sure the anchors are
seated flush with the concrete surface.
s
11
Install wall plate
01
with four washers
10
and screws
9
CAUTION:
Improper use could reduce the holding
power of screws
9
. DO NOT over-tighten the screws.
02
4-
4-
4-
4-
5-
5-
