8’ x 12’
Overlap Workshop
B
60360200A1
TRUSS SUPPORT QTY 2
OPA8PE
PLAIN END
OPA812WS
WINDOW PANEL
QTY 2
OPA812PS
PLAIN PANEL
QTY 2
WS12X8BRDFL
FLOOR QTY 2
C
D
E
G
I
F
45281757PTR
1757mmm BATTEN QTY 8
28120675PARPTR
675mm STRIP QTY 4
OPA8TRUSS
TRUSS
O
A
OPA812DD PARTS LIST
1
3
183513408
ROOF SHEET
QTY 4
DDRPT
DOOR QTY 2
OPA8DE
DOOR END
90121375PAII74PT
1375mm BARGE BOARD QTY 4
60151710PTR
1710mm CORNER STRIP QTY 6
45281835PTR
1835mm BATTEN QTY 4
H
K
L
M
J
2
45451630PTR
1630mm BATTEN QTY 1
R
N
H
Q
56120675PARPTR
675mm STRIP QTY 4
Important : Assembly of
this shed requires a
minimum of two adults.
REQUIRED TOOLS :
(NOT SUPPLIED)
Must Pre-drill for
each screw used.
PCWIN1
WINDOW QTY 6
Floor
80mm Screw
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
This building is pressure treated to ensure longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not need additional
treatment.
- This product must be built on a
solid level
base.
- Please keep all plastic bags and small parts away from
children.
- The roof of this building is not a load bearing structure.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
Technical Helpline:
0333 7777 089
8.30 am and 5.00
pm Monday to Friday.
Please check all parts prior to assembly
Assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled
to.
If the product is not constructed in accordance with the
instructions, or is altered in any way (e.g. painted), the
manufacturer cannot be held liable for any resulting damage.
The windows are packed
together tightly, separate before
assembly.
S
FIN20010512PT
FINIAL QTY 2
P
84996
675mm PLASTIC STRIP QTY 6
FELT
85052
QTY 3
PLAN VIEW
Screws
Place the panels on top of the completed floor. Make sure that all the panels are tight and flush before fixing them to each
other using 3x50mm screws.
On the window panels use an 80mm screw to fix the top of the panels and 2 x 50mm screws for the middle and bottom.
When the panels are secured to each other, make sure they are square and fix to the floor using 3x50mm screws for
each panel making sure the screws are located in to the bearers underneath.
Place the hinge against the inside of the door frame and position the large section of the hinge so
that it is flush with the inside of the framing as shown and fix with 25mm screws.
Open the hinge and fix the smaller section to the door framing. Again make sure that the hinge is
flush and that the holes are positioned so that the 25mm screws locate correctly into the batten.
N
Fix the 1630mm batten against the end of the door using
3x70mm screws. Make sure it is flush with the door end’s
framework.
Fix a turn button to the top and bottom of the batten using
1x30mm
(zinc)
screw for each.
4
Place and secure each angled block using 2x70mm screws.
Make sure these are 1470mm from the floor level and are
tight against the framework.
Place the truss so that is sits on the angled blocks. Secure
this in place by screwing down through the truss into the
blocks using 2 x 90mm screws for each end.
5
A
D
C
B
A
F
Q
R
I
HAMMER
SHARP KNIFE
SCISSORS
FLAT HEAD
SCREWDRIVER
POZI DRIVE
SCREWDRIVER
TAPE MEASURE
LADDER
P
O
Q
H
P
H
Board
Lip
Attention:
Take care when
placing the
screws. These
can not be
backed out.
You may need to
cut the plastic
strips to size using
a pair of scissors
Place the window from the outside so that the lip sits on the bottom board as shown.
Place the plastic strips at the top and bottom of the window so that one side butts up
against the cladding. Fix each strip in place using 2 x security screws.
Position the 675mm strips vertically on either side of each window, so that it overlap
both windows equally, and fix each with 2 x 25mm security screws.
Fixing Pack (OPA812DDFP)
This fixing pack is used for several products.
There may be additional fixings.
Not to Scale
Turn Button
Qty 2
Z’ bracket
Qty 16
70mm Screw Qty 7
50mm Screw Qty 36
10mm Felt tacks
Qty 110
25mm Screw Qty 61
30mm Screw Qty 18
30mm Nail Qty 90
Flush Hinge
Qty 4
25mm Countersunk
Security Screws Qty 40
Hasp & Staple
40mm Screw Qty 18
80mm Screw Qty 3
90mm Screw Qty 4
