background image

USER MANUAL 
200W LED MOVING HEAD SPOT BEAM WASH LIGHT                                                                                                                                                                                                                                                                               

User Manual---------1pc 

 

 SAFETY INFORMATION                                                                           

Important 

Every person involved with the installation, operation and maintenance of this device has to 

be  qualified  and  follow  the  instructions  of  this  manual.  Manufacturer  will  not  with 

responsibility for those operations which are not according to this Instruction.   

Verify that the voltage matches the rated voltage. 

When the voltage is 110V , Do not connect more than 10 lightings in total to AC mains 

power in one interconnected daisy chain   

When the voltage is 220V , Do not connect more than 20 lightings in total to AC mains 

power in one interconnected daisy chain   

Before  using  the  fixture,  check  that  all  power  distribution  equipment  and  cables  are  in 

perfect condition and rated for the current requirements of all connected devices. 

Always ground (earth) the fixture electrically. 

Avoiding hit the Light when you are move or install the light. 

The  minimum  distance  between  light-output  and  the  illuminated  surface  must  be  more 

than 0.5 meters. Keep all combustible materials (for example fabric, wood, paper) at least 

0.2 meters away from the fixture. 

Do not expose the fixture to rain or moisture. 

Avoid looking directly into the light source (especially those who suffer from epileptic fits) 

Maximum ambient temperature (Ta) is 40°C. Do not operate fixture at temperatures higher 

than this.   

The Maximum surface temperature is 50°C 

When suspending the fixture above ground level, verify that the structure can hold at least 

10 times the weight of all installed devices. 

Verify that all external covers and rigging hardware are securely fastened and use an 

approved means of secondary attachment such as a safety cable.   

To determine the power requirements for a particular fixture, see the label affixed 

to the back plate of the fixture or refer to the fixtures specifications chart. A fixture listed 

current rating is its average current draw under normal conditions. All fixtures must be 

directly powered off a switched circuit and cannot be run off a rheostat(variable resistor) or 

dimmer circuit, even if the rheostat or dimmer source voltage matches the fixtures 

requirement. Check the fixture or device carefully to make sure that if a voltage selection 

switch exists that it sets to the correct line voltage you will use. 

 

Warning! 

Verify that the voltage select switch on your unit matches the line voltage 

applied. Damage to your fixture may result if the line voltage applied does not match the 

voltage indicated on the voltage selector switch. All fixtures must be connected to circuits 

with a suitable Earth ground. 

 

 OPERATION INSTRUCTIONS     

                                                                                                   

 

The moving head is an LED wash light for onsite decoration purpose. 

 

Don’t turn on the fixture if it’s been through severe temperature difference like after 

transportation because it might damage the light due to the environment changes. So 

make sure to operate the fixture until it is in normal temperature. 

 

This light should be keep away from strong shaking during any transportation or 

movement. 

 

Don’t pull up the light by only the head, or it might cause damages to the mechanical 

parts. 

 

Don’t expose the fixture in overheat, moisture or environment with too much dust 

when installing it. And don’t lay any power cables on the floor. Or it might cause 

electronic shock to the people.   

 

Make sure the installation place is in good safety condition before installing the 

-02- 

03 

02 

Summary of Contents for FO-LM200C











Reviews: