manualshive.com logo in svg

Ford Thunderbird 2004, Owner'S Manual

Share
Download
Ford Thunderbird 2004 Owner'S Manual Download Page 44

Increasing speed while using speed control

There are two ways to set a higher
speed:

•

Press and hold the SET + control
until you get to the desired
speed, then release the control.
You can also use the SET +
control to operate the Tap-Up
function. Press and release this
control to increase the vehicle set
speed in small amounts by
1.6 km/h (1 mph).

•

Use the accelerator pedal to get to the desired speed. When the
vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control

There are two ways to reduce a set
speed:

•

Press and hold the SET - control
until you get to the desired
speed, then release the control.
You can also use the SET -
control to operate the Tap-Down
function. Press and release this
control to decrease the vehicle
set speed in small amounts by
1.6 km/h (1 mph).

•

Depress the brake pedal or
CANCEL until the desired vehicle
speed is reached, press the SET
+ control.

2004 Thunderbird

(tbr)

Owners Guide (post-2002-fmt)
USA English

(fus)

Driver Controls

44

Summary of Contents for Thunderbird 2004

































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands