Ford PERFORMANCE M-6007-X2302E Manual Download Page 13

Page: 13 / 25

M-6007-X2302E

Crate Engine

GUIDE

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF

FORD PERFORMANCE PARTS.

Techline 1-800-367-3788

Page 13 of 25

IS-1850-0632

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356

TECHNICAL SPECIFICATIONS

Crate Engine Part Number

M-6007-X2302E

Engine Type

302 Small Block

Displacement (cubic inches)

302

Horsepower Rating

340 HP STP cor. @ 6200 rpm

Torque

330 lb* ft STP cor. @ 4800 rpm

Block M-6010-BOSS302

Cast Iron; 4 Bolt Main (center 3)

Bore

4.000

Stroke

3.000

Crankshaft

Forged Steel (Flywheel bolts require sealer)/ 0 balance

Vibration Damper

M-6316-D302 Neutral Balance

Connecting Rod

Forged Steel

Piston

Forged Aluminum

Camshaft

Hydraulic Roller

Cam Timing

Position "0" (multi index crank sprocket)

Camshaft Lobe Separation

110°

Camshaft Duration

220°/220° @ .050" lift (int./ex.)

Camshaft Lift

.498/.498” (int./ex.)

Cylinder Head

M-6049-X2 Aluminum

Chamber Volume

63cc

Valve Diameter Int./Ex.

1.940" Int./1.540 Ex.

Compression Ratio

9.0:1

Rocker Arm

Aluminum Roller 1.60:1 Ratio

Recommended Timing

34°BTDC Total 4000 rpm (91 octane fuel R+M/2 minimum)

Maximum Rated rpm

6500 rpm

Oil Pan

79-94 stock style Mustang

Oil Filter

M-6731-FL1A

Oil Pressure

40 psi @ 240° F/ 4000 rpm

Recommended Oil

10w-30 or 10w-40

Max Oil Temperature

240° F

Recommended Coolant Temperature

195° F

Spark Plugs

AGSP-32C

Firing Order

1-3-7-2-6-5-4-8

Fuel Pressure (@ carburetor)

6-7 psi

Recommended Parts Not Included

M-12259-M302

Universal Spark Plug Wire Set

M-12259-M301

Pre-fit black Spark Plug Wire Set

M-6375-D302

Neutral Balance Flywheel (may require M-6397-A302 metric bolt

kit dependent on clutch)

M-4216-A210

Flywheel Bolts (note threads have required sealer pre applied)

M-9439-A50

Intake gasket (included)

*Oil pressure fitting in the left front block is ½ pipe thread, 40 lb*ft. torque max.

Summary of Contents for PERFORMANCE M-6007-X2302E


























Search results

Summary of Contents for PERFORMANCE M-6007-X2302E

Reviews:

Related manuals for PERFORMANCE M-6007-X2302E

Brands by name

Popular brands

Ford PERFORMANCE M-6007-X2302E, Manual

Search results

Summary of Contents for PERFORMANCE M-6007-X2302E

Reviews:

Related manuals for PERFORMANCE M-6007-X2302E

Brands by name

Popular brands