manualshive.com logo in svg

Ford Mustang Shelby GT500, Supplement Manual

Share
Download
Ford Mustang Shelby GT500 Supplement Manual Download Page 42

AIR FILTER

WARNING:

To reduce the risk of vehicle damage or personal

burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

See

scheduled maintenance information

for the appropriate intervals

for changing the air filter element.

When changing the air filter element, use only the Motorcraft® air filter
element listed. See

Motorcraft Part Numbers

in the

Capacities and

Specifications

chapter.

Changing the Air Filter Element

1. Loosen the air filter clamp bolt
enough to allow the air filter to slip
off the air filter housing easily.

2. Slip the air filter off from the air
filter housing.

3. Wipe the air filter housing clean
to remove any dirt or debris.

4. Install the new air filter taking
care not to damage the air filter
element. Align the tab on the closed
end of the filter with the notch in the air filter housing.

5. Tighten the air filter clamp bolt.

Maintenance

41

2014 05+ Mustang

(197)

Supplement, 1st Printing, December 2012
USA

(fus)

Summary of Contents for Mustang Shelby GT500

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands