manualshive.com logo in svg

Ford F181-20A, Instruction Manual, Page: 16 / 24

Share
Download
Ford F181-20A Instruction Manual Download Page 16

 

Original Instruction Manual 

EN

 

Copyright © 2014 

P a g e

 | 

14

 

www.Ford-tools.com 

WARNING: 

Before making any adjustments ensure the angle grinder is switched 

off.  

!

 

Hold the grinder with one hand and the battery pack (11) with the other.  

!

 

To install: pull and slide battery pack into battery port, make sure the release 
button (10) on the front side of the battery snap into place and battery is 
secure before begging operation.  

!

 

To remove: use your thumb or fingers, press the battery release button in and 
pull the battery pack off at the same time.  

8.3

 

Fitting the auxiliary handle (Fig. 1) 

The auxiliary handle (6) can be attached to the angle grinder in 2 different 
positions: left and right.  

8.4

 

Assembly the protective guard (Fig. 2 – 3) 

Fig 2 : 

a : Shaft 

fig 3 : 

 a : Hexagon wrench 

 b : Hexagon nut 

!

 

Loosen the clip of the protective guard (7) by pulling lock lever of protective 
guard (1) outward. 

!

 

Turn the protective guard so that uncovered part of the disc is as far apart as 
possible from the hand on main handle (3). 

!

 

Fix the protection guard by pushing the lock lever 

inwards

 (the protective 

guard should no longer be able to move).  

NOTE:

 If the protective guard can not be fixed firmly by the lock lever (1), use a 

hexagon wrench to tighten the hexagon nut.  

Disc guard  

CAUTION!

 The machine should be used only with guard. 

The position of the disc guard can be adjusted to suit the working conditions.  

The protective guard must be replaced if damaged. 

 

             WARNING 

Summary of Contents for F181-20A

























Reviews:

No comments