Ford 1999 Explorer Page 65 Owner'S Manual Download

Page: 65 / 264

Bass adjust

The bass adjust control allows you
to increase or decrease the audio
system’s bass output.

Press the BASS control then press:

•

to decrease bass output and

•

to increase bass output.

Treble adjust

The treble adjust control allows you
to increase or decrease the audio
system’s treble output.

Press the TREB control then press:

•

to decrease treble output and

•

to increase treble output.

Speaker balance adjust

Speaker sound distribution can be
adjusted between the right and left
speakers.

Press the BAL control then press:

BASS

TREB

SEL

BASS

TREB

SEL

BAL

FADE

Controls and features

Summary of Contents for 1999 Explorer









































































































































































































































































Search results

Summary of Contents for 1999 Explorer

Reviews:

Related manuals for 1999 Explorer

Brands by name

Popular brands

Ford 1999 Explorer, Owner'S Manual

Search results

Summary of Contents for 1999 Explorer

Reviews:

Related manuals for 1999 Explorer

Brands by name

Popular brands