background image

Forced

   

Aeromotive

   

Technologies

 

 

FAA-STC SA10232SC 

Supercharged O-470-L, -R, -S, and -U Engines in  

Cessna Models 182B, C, D, E, F, G, H, J, K, L, M, N, Q, and R Aircraft   

Instructions For Continued Airworthiness 

DOCUMENT NO. 22001-05 

REV G, August 21, 2020 

PAGE 2 OF 11 

LOG OF REVISIONS 

Revision 

Number 

Revision 

Date 

Approval 

Affected 

Pages

Description of Revision 

IR 

03/05/2004 

All 

New 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

08/06/2004 

 
 
 
 
 
 

01/04/2005 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

06/17/2006 

 

 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 
 
 

10 11 12 

13 

 

All 

 
 

5, 8 

 
 
 

 
 

10 

 
 
 
 
 

13 

 
 
 

11 

 

13 

5.3, para 2. Alignment marks for 

boost cutoff closed position 

changed to match installation 

instructions, II-182. 

 

Parts list added. 

 

Cessna 182 Q and R models and 

O-470-U engines added to header

 

Cessna 182 Q and R models and 

O-470-U engines added to 

section 2 and 15. 

 

O-470-U added to section 15, 

engine operation 

 

Kit # changed to match PMA 

Cessna 182 Q and R models and 

O-470-U engines added to 

eligibility list 

O-470-U pulley added 

Heat shields added 

 

Weldon fuel pump P/Ns A8164A 

and A8164B added to parts list. 

 

Editorial correction 

 

Belt added 

 

12/21/2008 

10 
13 

Multi-groove belt replacement 
Added item 5, 6, 18. 
Added item 103, 104. 

2/27/2013 

10-13 

Removed kit list. 

Summary of Contents for FAA-STC SA10232SC












Reviews: