manualshive.com logo in svg

FOR-A USF-105DADA, Operation Manual

Share
Download
FOR-A USF-105DADA Operation Manual Download Page 6

6 

2. Panel Descriptions 

2-1. Front Panel 

 
 
 
 
 
 
 
 
 

USF-105DADA

 

 

No. 

Name 

Description 

(1) 

POWER LED 

Lights green when normal DC power is supplied by USF frame. 

(2) 

INPUT LED

 *1

 

Lights when input signal is detected. 

(3) 

TERM LED 

On 

Input signal impedance is set to 75

Ω. 

Off 

Input signal impedance is set to 1k

Ω. 

(4) 

MODE LED 

On 

LEDs to confirm signal mode. One of the LED from AES, 
LTC, or WC is lit to indicate current signal mode. 

Flash 

or 

Off 

When LEDs are flashing or all LEDs are turned off, card 
switches are incorrectly set. See Sec. 4 

“Signal Mode 

Settings

” for correct switch settings. 

(5) 

OUTPUT GAIN 
OUT1 to OUT5 

LTC/ 
Word Clock Distribution Mode 

About ±3.0dB of gain adjustment 
is available per output port. 

AES Distribution Mode 

Output gain is not adjustable. 

(6) 

USB Connector 

Used for USF-105DADA software version upgrades. 
(Do not connect a USB device.) 

*1

 

Input is not detected when input signal is distributed via USF-212/212S Internal Bus. 
INPUT LED turns off. 

 
 

(5) 

(6) 

(1) to (4) 

 

AES 

 

LTC 

 

WC 

 

POWER 

MODE 

 

INPUT 

 

TERM 

Summary of Contents for USF-105DADA






















Reviews:

No comments

Brands by name

Popular brands

Load more brands