background image

37

3.6.1. Per trasformazioni da METANO a PROPANO

- Open the front panel of the boiler, (§ 3.2.7.1.).

- For model KR 55, unscrew the outlet connection to the gas valve  

  (

A

 in Fig. 24).

  For model KR 85, unscrew the connecting pipe between the gas  

  valve and the fan  (

D

 in Fig. 23).

- Replace the existing diaphragm with one for PROPANE (Tables 3  

  and 4).

- Make the reconnection  (

A

 in Fig. 24 for KR 55 and 

D

 in Fig. 23  

  for KR 85).

- Refer to § 3.6.3.

3.6.2. Switching from PROPANE to METHANE

- Open the front panel of the boiler, (§ 3.2.7.1.).

- For model KR 55, unscrew the outlet connection to the gas valve  

  (

A

 in Fig. 24).

  For model KR 85, unscrew the connecting pipe between the gas  

  valve and the fan  (

D

 in Fig. 23).

- Replace the existing diaphragm with one for METHANE (Tables 3  

  and 4).

- Make the reconnection  (

A

 in Fig. 24 for KR 55 and 

D

 in Fig. 23  

  for KR 85).

- Refer to § 3.6.3.

3.6.3. Regulating the burner

Setting maximum heat output

Setting maximum heat output
- Turn the maximum heat output regulator 

 (Fig. 19) to MAXI  

  MUM (fully clockwise). Maximum heat output setting is displayed  

  on the LCD as a percentage of the boiler’s maximum value. 
- position selector 

2

 (fig. 1) to WINTER;

- check that the optional ambient thermostat (optional) is set to ON;

- activate the chimney-sweep mode (§ 3.2.7.1);

adjust CO2 in flue gas by turning the ratio regulator B (Fig. 24 for  

  KR 85 and Fig. 25 for KR 85) and make sure it is within the limits  

  of Table 12;
- operate the boiler on chimney-sweep mode and move to “Mini 

  mum heat output regulation”;

Minimum heat output regulation

- Rotate the regulator (Fig. 19) fully anticlockwise to set the maxi 

  mum heat output to MINIMUM.

  The display shows the desired maximum heat output as a per 

  centage of the boiler’s maximum heat output.

- Regulate the CO2 in flue gas by turning the offset regulator C  

  (Fig. 24 for KR 85 and Fig. 25 for KR 85) and make sure it is    

  within the limits of Table 12;

- To terminate the chimney-sweep operating mode, set knob 2  

  (Fig. 1) to any position other than WINTER and then to the desi 

  red position.

Value of carbon dioxide in the flue gas

Combustibile

Valore della CO

2

Metano

8,8 ÷ 9,2

Propano

9,8 ÷ 10,2

Tabella 12 - Valori di CO

2

2

fig. 22

Gas valve 

fig. 24

A

B

C

Gas valve 

fig. 23

KR 55

KR 85

fig. 25

D

KR 85

KR 55

B

C

Summary of Contents for KR 55













































Reviews: