background image

4

Installation

Installing legs – required

  1.  Remove legs from plastic bag packed inside refrigerator.

  2.  Tip refrigerator back and screw legs in all the way to stop (they will 

extend 1/8" below base of REF).

  3.  Adjust legs as needed to level REF in both directions. To access legs, 

remove the lower front panel. Turn legs clockwise to extend legs.

Installing shelves – required

  1.  Remove shelves and shelf brackets packed inside refrigerator.  

(If ordered, fi nd cut-out upper shelf accessory in separate box.)

  2.  Install shelf brackets in pilasters (insert top tab, squeeze and push in 

lower tab).

  3.  If ordered, position cut-out upper shelf accessory below evaporator 

with cut-out around drain.

Changing temperature controller settings – optional

Follett’s temperature controller is pre-programmed with a 34 F set point 
and °F display. The 34° set point delivers a temperature range of 34 F – 
38 F that may not meet the needs of your specifi c application. Follett’s 
controller set point can be changed to deliver the required range in either 
°F or °C. Refer to page 6 for instructions on changing set point and/or 
display to °C.

2

1

3

Fig. 1

Fig. 2

Fig. 3

Summary of Contents for REF Series

















Reviews: