background image

5

Specifi cations

Electrical

Each ice machine requires its own separate circuit with electrical disconnect within 10 ft (6m). 
Equipment ground required. 
Standard electrical – 220-240/50/1
Maximum ice machine fuse – 20 amps
Amperage – 16 amps
Maximum power – 5280 watts
Climatic class – N
6 ft (2m) cord provided on ice machine

 

CAUTION

•  Plug must be provided by the end-user and must conform to standard EN 60 335-2-24:2003 of the end 

destination

•  If the supply cord is damaged, it must be replaced by the manufacturer or their service agent, or a similarly 

qualifi ed technician in order to avoid a hazard

Plumbing

3/8" OD push-in water inlet
3/4" MPT drain
1/4" FPT condenser inlet (water-cooled condenser only)
1/4" FPT condenser drain (water-cooled condenser only) 

Notes:

  3/4" vented drain line must slope a minimum of 1/4" per foot (6mm per 30.4cm run).

 

Drain to be hard piped and insulated.

 

To prevent back fl ow, do not connect drains.

 

Separate drains for ice machine and condenser.

 

Water shut-off recommended within 10 feet (3m).

 

Follett recommends installation of Follett model 00130286 activated carbon fi lter in ice machine inlet water  

 line.

Ambient

Air temperature  

 

100 F/38 C max. 

 

50 F/10 C min.

Water temperature 

 

90 F/32 C max.  

 

45 F/7 C min.

Water pressure – potable 

70 psi max. (483 kPa)   

10 psi min. (69 kPa)

Note:

  Water-cooled condenser pressure 150 psi max (1034kPa); 10 psi min (69kPa)

Heat rejection

Air-cooled rejects 15,500 BTU/hr to air (3906Kcal/hr) to air
Water-cooled rejects 15,500 BTU/hr to water (3906Kcal/hr) to water

Ice production

F

C

50
10
60
16
70
21
80
27
90
32

60
16

1367

620

1287

584

1219

553

1160

526

1109

503

70
21

1293

586

1211

549

1140

517

1078

489

1026

465

80
27

1175

533

1119

508

1062

482

1006

456
950
431

90
32

1083

491

1047

475

999
453

969
439
882
400

100

38

994
451
957
434
914
415
868
394
821
372

lbs
kg
lbs
kg
lbs
kg
lbs
kg
lbs
kg

Inlet W

a

ter 

T

emper

atur

F/C

Ambient Air Temperature F/C

Air-cooled ice machine capacity/24 hrs.

F

C

50
10
60
16
70
21
80
27
90
32

60
16

1360

617

1318

598

1291

586

1249

567

1207

548

70
21

1313

596

1272

577

1244

564

1202

545

1160

526

80
27

1267

575

1225

556

1197

543

1155

524

1114

505

90
32

1220

553

1178

534

1150

522

1108

503

1067

484

100

38

1173

532

1131

513

1103

501

1062

482

1020

463

lbs
kg
lbs
kg
lbs
kg
lbs
kg
lbs
kg

Water-cooled ice machine capacity/24 hrs.

Inlet W

a

ter 

T

emper

atur

F/C

Condenser Water Temperature F/C

Summary of Contents for HCE1400A









































Reviews: