Foerster TAK5-CH1-25 Instruction Manual Download Page 141

Page: 141 / 226

Cleaning

141

If the automatic feeder is equipped with the

cleaning kit, the

detergent is dosed all-automatically and the cleaning water is

drained all-automatically via the mixer draining valve.

If the automatic feeder is not equipped with the

cleaning kit,

after pre-cleaning you can pour some detergent into the mixer

jar, if required.

With

you can all-automatically drain the cleaning water via the

teat by means of the training pump. However, make sure that

during the cleaning process no animal is sucking at the teat.

Alternatively you can also tip over the mixer. In that case, you

must deactivate beforehand the function

mixer emptying via

the teat

With

you can drain the cleaning water via the mixer draining

valve.

9.2.1

Starting mixer cleaning automatically/time-controlled

cleaning

mixer

2. Enter the number of cleaning cycles in

cleaning/day

3. Enter the desired time in

cleaning 1, 2...

If the cleaning cycle is completed, the message on the right is

displayed.

Note

: If mixer cleaning does not take place at the en-

tered time, the reason for it may be that heat exchanger

cleaning is taking place simultaneously or has been car-

ried out before. The same applies if between heat ex-

changer cleaning and mixer cleaning no feed has been

claimed. In that case, too, mixer cleaning will not take

place.

mixer cleaning

start?

cleaning/day: 1

cleaning 1 22:00

Summary of Contents for TAK5-CH1-25



































































































































































































































Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands

Foerster TAK5-CH1-25, Instruction Manual

Search results

Summary of Contents for TAK5-CH1-25

Reviews:

Related manuals for TAK5-CH1-25

Brands by name

Popular brands