background image

3

Compliance Information Statement: Declaration of Compliance procedure

Product Identification:      Focusrite RedNet
Responsible party:             American Music and Sound
Address:                              4325 Executive Drive
                                              Suite 300
                                              Southaven
                                              MS 38672

Telephone:                           800-431-2609

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause 

harmful  interference,  and  (2)  this  device  must  accept  any  interference  received,  including  interference  that  may  cause  undesired 

operation.

ENVIRONMENTAL DECLARATION

For USA

To the User:

1. Do not modify this unit! This product, when installed as indicated in the instructions contained in this manual, meets 

FCC requirements. Modifications not expressly approved by Focusrite may void your authority, granted by the FCC, to 

use this product.

2. Important: This product satisfies FCC regulations when high quality shielded cables are used to connect with other 

equipment. Failure to use high quality shielded cables or to follow the installation instructions within this manual may 

cause magnetic interference with appliances such as radios and televisions and void your FCC authorization to use this 

product in the USA.

3. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 

commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of 

this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct 

the interference at his own expense

For Canada
To the User:

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

The exclamation point within an equilateral triangle is intended to alert the user 

to the presence of important operating and maintenance (servicing) instructions 
in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS 

TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE 

PLACED ON THIS APPARATUS.

The lightning flash with arrowhead symbol, within equilateral triangle, is intended 

to alert the user to the presence of uninsulated “dangerous voltage” within the 

product’s  enclosure  that  may  be  of  sufficient  magnitude  to  constitute  a  risk  of 

electric shock to persons.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER 

(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. 

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RoHS Notice

Focusrite Audio Engineering Limited has conformed where applicable, to the European Union’s Directive 2002/95/EC on Restrictions 
of Hazardous Substances (RoHS) as well as the following sections of California law which refer to RoHS, namely sections 25214.10, 
25214.10.2, and 58012, Health and Safety Code; Section 42475.2, Public Resources Code.

Summary of Contents for REDNET 1

















Reviews: