Focusrite ISA 428 Pre Pack User Manual Download Page 14

ENGLISH

14

Warranty

All Focusrite products are covered by a warranty against
manufacturing defects in material or craftsmanship for a
period of one year from the date of purchase. Focusrite in
the UK, or its authorised distributors worldwide, will do
their best to ensure that any fault is remedied as quickly as
possible. This warranty is in addition to your statutory
rights.

This warranty does not cover any of the following:

 

Carriage to and from the dealer or factory for
inspection or repair.

 

Labour charge if repaired other than by the distributor
in the country of purchase or Focusrite in the UK.

 

Consequential loss or damage, direct or indirect, of any
kind, however caused.

 

Any damage or faults caused by abuse, negligence,
improper operation, storage or maintenance.

If a product is faulty, please first contact the dealer from
which the product was purchased. If the product is to be
shipped back, please ensure that it is packed correctly,
preferably in the original packing materials. We will do our
best to remedy the fault as quickly as possible.

Please help us to serve you better by completing and
returning the Warranty Registration Card, or registering
online at http://www.focusrite.com. Thank you.

Accuracy

Whilst every effort has been made to ensure the accuracy
and content of this manual, Focusrite Audio Engineering Ltd
makes no representations or warranties regarding the
contents.

Copyright

© 2002-2003 Focusrite Audio Engineering Ltd. All rights
reserved. No part of this manual may be reproduced,
photocopied, stored on a retrieval system, transmitted or
passed to a third party by any means or in any form without
the express prior consent of Focusrite Audio Engineering
Ltd.

ADAT™ is a registered trade mark of Alesis Corporation
Inc.

192 HD™ is a registered trade mark of Digidesign Inc.

Summary of Contents for ISA 428 Pre Pack















Reviews: