The Nero LCD electric heater provides convected heating in conjunction with a LCD screen which can display a number of different fuel effects
and scenes. The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be
located in any household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future
reference and pass on as necessary to subsequent owners of the appliance.
•
DO NOT
use this appliance immediately below a fixed socket outlet.
•
DO NOT
use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could present a
hazard.
•
CAUTION:
This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that will
switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.
•
WARNING :
This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar material. A
clearance space of at least one metre should be allowed in front of the appliance.
The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly over or above the heater unit. If
the cord is damaged, it must be replaced by a service agent or competent person.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The LCD displays are produced using highly accurate technology, however, black pixels may be found, or red, blue and green pixels may not disap-
pear. This is perfectly normal and within product specification. This should not be regarded as a fault.
The appliance is designed to be floor mounted only.
DO NOT RECESS ANY PART OF THE APPLIANCE.
The appliance is supplied with a pre-wired three pin BS1363 plug (13 Amp fuse rated), and 2 metre cable. A standard switched outlet/wall sock-
et, (including earth provision), must therefore be located within this distance, and be easily accessible in order to isolate the supply for mainte-
nance and cleaning. This socket
must not
be mounted behind or above the appliance.
IMPORTANT: THIS APPLIANCE MUST BE EARTHED.
The appliances are designed to be floor mounted. It is not necessary to secure the surround to the wall, provided it is sited on a firm level sur-
face.
It should be noted that the appliance creates warm convected air currents. These currents move heat from the room surroundings to, and up
the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco smoke) exist,
may slightly discolour wall finishing. Once the suite is in the desired location check that it is level and it sits firmly on the floor, i.e. does not rock
in any direction, and fits squarely against the wall.
Note: Skirting boards may need to be cut in order to fit the rear of the suite snugly against the wall, Provision must be made in the wall, either
behind the suite, or in one of the sides of the suite to allow the power supply cable to exit.
1.0 PRELIMINARY NOTES
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
©
2011 Focal Point Fires plc.
2
GB IE
©
2011 Focal Point Fires plc.
2.0 APPLIANCE DATA
3.0 ELECTRICAL INSTALLATION REQUIREMENTS
4.0 SITE REQUIREMENTS
Weight (kg):
37.5 kg
Dimensions (mm):
H 855 x W 850 x D 235
Voltage (Volts):
230-240V a.c. 50Hz
Heating Elements:
2 x 900/1000 Watts
Supply Cord:
2 metres
Supply Plug:
BS 1363, 13A Fused
Location:
Indoor Use
LCD Display:
40 Watts
Section Contents
Page No.
1.0
Preliminary Notes
2
2.0
Appliance Data
2
3.0
Electrical Installation Requirements
2
4.0
Site Requirements
2
5.0
Clearances to Combustible Materials
3
6.0
Unpacking the Appliance
3
Section Contents
Page No.
7.0
Component Checklist
3
8.0
Operating the Appliance
3
9.0
Safety Cut-Out System
4
10.0
Cleaning and Maintenance
4
11.0
Servicing
5
12.0
Appliance Dimensions
5
