background image

13

EN

Trouble shooting

Problem

Possible Cause

Solution

Aircraft will not respond to 

the throttlebut responds to 

other controls.

-ESC is not armed.

-Throttle channel is reversed.

-Lower throttle stick and throttle trim to lowest  settings.

-Reverse throttle channel on transmitter.

Extra propeller noise or 

extra vibration.

-Damaged spinner, propeller,

 motor or motor mount.

-Loose propeller and spinner parts.

-Propellor installed backwards.

-Replace damaged parts.

-Tighten parts for propeller adapter, propeller and spinner.

-Remove and install propeller correctly.

Reduced flight time or 

aircraft underpowered.

-Flight battery charge is low.

-propeller installed backward.

-Flight battery damaged.

-Completely recharge flight battery.

-Replace flight battery and follow flight battery 

 instructions.

Control surface does not 

move, or is slow to respond 

to control inputs.

-Control surface, control horn,

 linkage or servo damage.

-Wire damaged or connections 

 loose.

-Replace or repair damaged parts and adjust controls.

-Do a check of connections for loose wiring.

Controls reversed.

Channels are reversed in the 

transmitter.

Do the control direction test and adjust controls for 

aircraft and transmitter.

-Motor loses power

-Motor power pulses then 

 motor loses power.

-Damage to motor, or battery.

-Loss of power to aircraft.

-ESC uses default soft Low Voltage

 Cutoff(LVC).

-Do a check of batteries, transmitter, receiver, ESC, motor 

 and wiring for damage(replace as needed).

-Land aircraft immediately and recharge flight battery.

LED on receiver flashes 

slowly.

Power loss to receiver.

-Check connection from ESC to receiver.

-Check servos for damage.

-Check linkages for binding.

Spare parts list content

FMSRQ101

FMSRQ102

FMSRQ103

FMSRQ104

FMSRQ105

FMSRQ106

FMSRQ107

FMSRQ108

FMSRQ109

FMSRQ110

FMSRQ111

FMSRQ112

FMSRQ113

FMSRQ114

FMSRQ115

FMSRQ116

FMSRQ117

FMSRQ118

Fuselage

Main Wing Set

Vertical stabilizers

Horizontal Stabilizer

Cockpit

Bomb and Missile Set

Twin Engine Compartment

Foam part (Laser racker)

Foam part (fin)

Scale Plastic Parts Set

Control Horns

Linkage Rod

Screw Set

LED

Front Landing Gear Set

Main Landing Gear Set

Front Landing Gear System

Main Landing Gear System

FMSRQ119

FMSRQ120

FMSRQ121

FMSRQ122

FMSCON010

FMSRE027

FMSRE032

FMSDF12B70

PRKV1850

PRESC027

PR13MGAP

PR13MGAR

PR23MGAP

FMSSEQ6S-1

Carbon fiber spars

Front Landing Gear Door

Wheel Set

Decal Sheet

Multi Connector System10

EL-retract

EL Retract 

Ducted fan (12-blade)

2860-KV1850 motor

80A  ESC X 2 with 8A BEC

Predator 13g analog metal gear servo positive

Predator 13g analog metal gear servo reverse

Predator 23g analog metal gear servo positive

Sequencer-6 sec 

Visit our website: www.fmsmodel.com to see photo of this product. Enter the key word "ESC" in the search bar for the 

stock ESC instruction manual.

Summary of Contents for A-10 Thunderbolt II V2














Reviews: