FMI (V)KC36NE series Owner'S Operation And Installation Manual Download Page 26

Page: 26 / 40

www.fmiproducts.com

116238-01L

between burner assembly and side of

firebox (see Figure 40).

10. Install right brick panel using same

method described in step 6 for left brick

panel.

11. Replace deflector shield using screws

removed in step 7.

12. Using screws removed in step 6, replace

plenum and attach to burner.

13. Carefully replace the ember pod and log

set.

14. Use screws removed in step 4 to replace

andiron assembly.

15. Install lava rock and glowing embers. See

Installing Lava Rock and Glowing Embers,

page 25.

16. Close glass door and lock latches on top

and bottom of door and replace screen.

See

Removing Glass Door

, steps 5 and

6, page 25.

17. Replace top and bottom louvers.

FIREPLACE

INSTALLATION

Continued

Figure 40 - Installing Rear Brick Panel

Rear Brick Panel

Left Side Brick

Panel

WALL SWITCH INSTALLATION

Installation of a wall switch allows you to

activate gas control valve and turn fireplace

on and off. Wall switch is to be connected to

incoming 120 volt regular household wiring

that supplies electricity to fireplace.

OPTIONAL REMOTE CONTROL

INSTALLATION (MODEL WRC)

Note: If using optional wireless hand-held

remote control, wall switch must be in the ON

position to be operational. Remote control

then becomes the switching mechanism for

fireplace operation.

1. Open lower louver panel.
2. The WRC model receiver does not require

INSTALLING BRICK LINER MODELS

BL36D-A(S-A) AND BL36DH-A(S-A)

WARNING: If fireplace has

been running, turn off unit. Let

cool before installing brick liner.

You may purchase brick liner from your local

retailer or see

Accessories

, page 35.

CAUTION: Always handle

brick panels with two hands.

Do not force brick panels into

place. Excessive force will break

brick panels.

1. Remove top and bottom louvers to allow

access to door latches.

2. Unlock door latches and open glass door.

See

Removing Glass Door

, steps 1 and

2, page 25.

3. Carefully remove lava rock and ember

material.

4. Remove and iron assembly from plenum

by removing screws.

5. Carefully lift logs and ember pod from

burner

6. Remove screws that attach plenum to

burner to remove plenum.

7. Remove three screws from deflector

shield on inside top of firebox. Set shield

and screws aside.

8. Install rear brick panel first. Rest bottom

edge of panel on back edge of burner

assembly (see Figure 40).

9. Install left side brick panel by sliding it

Figure 39 - Placing Ember Material on

Burner

Ember Material

Plenum

Andiron

Summary of Contents for (V)KC36NE series









































Search results

Summary of Contents for (V)KC36NE series

Reviews:

Related manuals for (V)KC36NE series

Brands by name

Popular brands

FMI (V)KC36NE series, Owner'S Operation And Installation Manual

Search results

Summary of Contents for (V)KC36NE series

Reviews:

Related manuals for (V)KC36NE series

Brands by name

Popular brands