background image

 For more information, visit www.fmiproducts.com

 

WARNING: If the information in this manual is not 

followed exactly, a fire or explosion may result causing 

property damage, personal injury or loss of life.
—  Do  not  store  or  use  gasoline  or  other   flammable 

vapors and liquids in the  vicinity of this or any other 

appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any 

phone in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

—  Installation and service must be performed by a quali

-

fied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference.

Direct-vent FirePLAce

OWner’S OPerAtiOn AnD inStALLAtiOn MAnUAL

MODeLS (v)DvF36nS, (v)DvF36PS, (v)DvF36nh, (v)DvF36Ph, 

DvF-36nS-hA, DvF36nh-hA, (v)DvF42nS, (v)DvF42PS, (v)

DvF42nh, (v)DvF42Ph, DvF-42nS-hA, AnD DvF42nh-hA

PFS

®

US

Summary of Contents for (V) DVF42NH









































Reviews: