background image

For more information, visit www.fmiproducts.com

SAVE THIS BOOK

This book is valuable. In addition to instructing you 
on how to install and maintain your appliance, it also 
contains information that will enable you to obtain re-
placement parts or accessory items when needed. Keep 
it with your other important papers.

This fireplace is approved for use as a wood burning 
fireplace or for use with a vented gas log approved to 
ANS Z21.60, Z21.84 standards or for use with a vent-free 
gas log heater approved to ANS Z21.11.2 standard. A FMI 
PRODUCTS, LLC hood must be installed when using a 
vent-free gas log set (see Accessories
, page 16).

This wood burning fireplace complies with UL127-
CAN/ULS-S610-M87 standard as a FACTORY BUILT 
APPLIANCE and is listed and tested by the PFS Cor-
poration.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

36" OPEN CORNER CIRCULATING (LOUVERED)  

WOOD BURNING FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

OPEN CORNER WOOD BURNING FIREPLACE

(V)36R(S) Right Side Opening; (V)I36R(S) Right Side Opening (Fully Insulated)

(V)36L(S) Left Side Opening; (V)I36L(S) Left Side Opening (Fully Insulated)

ICC-ES #ESR-2542

PFS

®

US

C

Summary of Contents for 36L Series





















Reviews: