FMG PL245 Operator'S Manual Download Page 6

 

OPERATORS MANUAL D0005D  

 

 

BULLDOZER BLADE 

 

Page 6 

1. SAFETY INSTRUCTIONS 

 

This section summarizes the regulations that must always be followed when working with the 
bulldozer blade. However, these regulations do not exempt the driver from statutory and other 
national  regulations  regarding  traffic  safety  and  occupational  health  and  safety.  Safety 
regulations  that  apply  to  different  types  of  working  sites  and  existing  road  traffic  laws  must 
always  be  observed.  Tractor  safety  regulations  accepted  by  the  Finnish  occupational  safety 
and health administration have already been taken into account in the equipment design. The 
following  section  describes  general  safety  precautions  that  must  be  observed  regarding  the 
use of the bulldozer blade. 

 

IMPORTANT 

Do not use the bulldozer blade for other purposes than it has been 
designed. Please read this manual carefully before using the implement. 

 

IMPORTANT 

Before driving, make sure that all movements and functions work 
correctly.  

 

DANGER 

When testing different movements of the bulldozer blade make sure that 
there is no one close to tractor. Safety distance 5 meters. 

 

IMPORTANT 

Advise other users on the use of the implement and ask them to read the 
manual.  

 

DANGER 

Do not operate with the damaged implement. 

 

IMPORTANT 

Use the rotary beacon while working 

Summary of Contents for PL245
















Reviews: