FS-SR8C
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
对码
Binding
The firmware of this receiver can be updated through the FlyskyAssistant (Only version 3.0 or above is supported. The firmware
of FlyskyAssistant is available on the Flysky official website).
This receiver can be updated via the following two ways:
1. After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the
computer, then open the FlyskyAssistant on the computer to update the firmware.
2. Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following
way
(The LED of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on the
computer to update the firmware.
• Connect the signal pin of the CH3 to the signal pin of the CH4 first, then power on the receiver.
固件更新
Firmware update
本接收机固件更新需通过富斯遥控管家（FlySkyAssistant）完成（仅 3.0 及以上版本支持，富斯遥控管家固件可从官网 www.flysky-
cn.com 获取）。
本接收机可以通过以下两种方式进入更新：
1. 先将发射机与接收机对码后（接收机 LED 灯常亮），再将发射机与电脑连接，然后在电脑端打开富斯遥控管家，通过富斯遥控管家
进行固件更新；
2. 将发射机与电脑连接，参考如下方式使接收机进入强制更新状态（接收机 LED 灯状态三闪一灭），然后在电脑端打开富斯遥控管家，
通过富斯遥控管家进行固件更新。
进入强制更新状态的操作方式如下：
• 先将接收机 CH3 和 CH4 通道的信号端相连接，然后给接收机通电。
接收机支持双向对码和单向对码（双向对码完成后发射机将显示接收机回传的信息），因此对码前需先在发射机端设置单向或双向对码。如需对码
接收机与发射机，对码步骤如下所述。
双向对码步骤：
1. 发射机选择双向通信，然后进入对码状态；
2. 接收机上电进入对码状态，接收机 LED 灯快闪；
3. 接收机 LED 灯常亮，即对码成功，发射机对码成功后自动退出对码状态，对码完成；
4. 检查发射机、接收机是否正常工作。如需重新对码，请重复以上步骤。
单向对码步骤：
1. 发射机选择单向通信，然后进入对码状态；
2. 接收机进入对码状态，此时接收机 LED 灯快闪；
3. 接收机 LED 灯慢闪，即对码成功。发射机则需手动将其退出对码状态，接收机 LED 灯常亮，对码完成；
4. 检查发射机、接收机是否正常工作。如需重新对码，请重复以上步骤。
The receiver automatically enters the bind state upon power-on. That is, the receiver waits for 1 second after power-on, it enters
the binding state if no connection is established with the transmitter. If the receiver enters the binding state and fails to bind
with the transmitter within 10 seconds, it exits the bind state. If the receiver has succeeded in binding with the transmitter earlier
(established a connection), it will continue to wait for a connection with the transmitter after the exit of the bind state.
• When this receiver and the transmitter complete the binding, please turn on the transmitter and then the receiver. If you turn
on the receiver first, there may be a wrong binding at this time when there is a similar transmitter in the bind state. Please
bear this in mind.
The receiver supports two -way binding and one-way binding. The transmitter will display the information returned from the
receiver after the two-way binding is completed. The receiver automatically enters the binding state once it is powered on, set
to Two way or not at the transmitter side first before starting binding.
Follow the steps below to bind in two-way binding:
1. At the transmitter side, set
Two way
in
Bind setting
menu, then put the transmitter into bind mode.
2. After the receiver is powered on, it will automatically enter the binding mode if it is not connected to the transmitter in 1 second.
3. When the LED of the receiver is solid on, the binding process should be completed. The transmitter exits the bind mode
automatically.
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any
problems arise.
Follow the steps below to bind in one-way binding:
1. At the transmitter side, set
One way
in
Bind setting
menu, then put the transmitter into bind mode.
2. Put the receiver into bind mode (Refer to the description for Two way binding above ).
3. When the LED of the receiver is in slow flashing state, the binding process should be completed.
You need to manually put the
transmitter to exit the bind mode.
Then the LED of the receiver is solid on, indicating that the binding is completed.
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any
problems arise.
Note: Put the transmitter into bind mode first, then put the receiver into bind mode. If the binding is not completed within ten
seconds, the LED of the receiver will enter its slow flashing state.
注：对码时请先将发射机进入对码状态，再将接收机进入对码状态；若 10S 内对码没有完成，接收机退出对码状态，LED 灯进入慢闪状态。
