FS-R4A
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
•
Low /high voltage alarm: When the receiver enters the low voltage protection, motor has no output, and all the lights flash slowly; when the receiver enters the high
voltage protection, all channels have no output. All car lights flash promptly.
车灯控制
Car light control
车灯控制主要是通过发射机的的设置实现车灯亮灯状态及亮灯模式的转换
。
1. 车灯开启与关闭的控制方式：
•
车灯控制分为四通道控制和两通道控制两种方式，打开发射机，手轮顺时针打到最大行程，打开接收机电源，可以实现两种控制方式的切换 ;
•
当切换为四通道控制时，CH3 最右为打开车灯，最左为关闭车灯；
•
当切换为两通道控制时，手轮快速顺时针打到最大行程两次，打开应急灯，重复动作则关闭；手轮逆时针打到最大行程打开示宽灯或者呼吸 / 爆闪灯，重复动作则关闭；
2. 车灯工作的四种模式状态：
•
普通模式：向左打转向，左转向灯慢闪，向右打转向，右转向灯慢闪；CH3 最右，前灯高亮，后灯低亮；刹车 / 后退，后灯高亮；按下 CH4，应急灯慢闪；
•
运动模式：向左打转向，左转向灯慢闪，向右打转向，右转向灯慢闪；前进，前灯高亮，刹车 / 后退，后灯高亮；按下 CH4，应急灯慢闪；
•
呼吸模式：所有车灯（含车顶灯、氛围灯）呼吸闪烁，CH3 最右打开所有车灯，CH3 最左关闭所有车灯；
•
爆闪模式：所有车灯（含车顶灯、氛围灯）爆闪，CH3 最右打开所有车灯，CH3 最左关闭所有车灯；
•
各工作模式切换方法：快速短按 CH4 两下切换模式；
•
以上方式为使用 CH3 控制照明 / 示宽灯或者应急灯，关于手轮控制详见 1 说明。
3. 氛围灯和车顶灯的工作模式 :
•
氛围灯和车顶灯包含单独模式和组合模式两种工作模式，在普通模式和运动模式下可以调节使用，在呼吸模式和爆闪模式中无法使用；单独模式下氛围灯和车顶灯各
自单独操控，互不干扰；组合模式下氛围灯和车顶灯共同工作，可以统一控制。手轮快速顺时打到最大行程 4 次可以切换两种工作模式。
•
组合模式下包含快闪、呼吸、关闭三种工作模式；手轮快速顺时打到最大行程 3 次可以切换不同的闪烁方式。
•
单独模式下氛围灯有呼吸、爆闪、三快闪一长灭和关闭四种工作模式，手轮快速顺时打到最大行程 3 次可以切换不同的模式；车顶灯有常亮、慢闪、关闭三种工作模
式 , 手轮快速逆时打到最大行程 3 次可以切换不同的工作模式。
注：
（1）若前后灯与实际控制相反时，需将前后灯控制方式进行反向，发射机开机状态下手轮保持逆时针打到最大行程，然后给接收机上电可以实现切换；若左右转向灯
与实际控制相反时，则仅需在车灯接口处对调一下左右灯线；
（2）若 CH1 设置了通道反向，则以上手轮操作均进行反方向操作（顺时针变为逆时针，逆时针变为顺时针）；
（3）车灯控制的方向 CH1 和油门 CH2 具有自动识别中位的功能。
The car light control is mainly to implement the changeover of lighting states and lighting modes by setting the transmitter.This receiver's car lights have
multiple prompt functions such as power-on self-check, overheating alarm and low/high voltage alarm,ect.
1. Control mode of the car light ON/OFF:
•
The car light control is divided into four-channel control and two-channel control. Switching between the two control modes can be implemented by turning on the
transmitter, turning the handwheel clockwise to the maximum stroke, and turning on the power supply of the receiver.
•
When switching to four-channel control, the rightmost position of CH3 turns on the car lights, and the leftmost position turns off the car lights.
•
When switching to two-channel control, turn the handwheel quickly to its maximum stroke twice clockwise to turn on the emergency light, and turn off by repeating
the action; Turn the handwheel counterclockwise to its maximum stroke to turn on the width indicator light or breathing/flashing light, and turn it off by repeating the
action.
2. Four modes/states of car light operation:
•
Normal mode: Turn the handwheel to the left, left turn signal flashes slowly; Turn the handwheel to the right, right turn signal flashes slowly; Set CH3 to its rightmost
position, the headlights enter into high-luminance state and the tail lights enter into their low-luminance state; When brake is applied/gearbox is shifted to reverse
gear, tail lights enter into their high-luminance state; Press CH4, the emergency lights flash slowly.
•
Sports mode: Turn the handwheel to the left, left turn signal flashes slowly; Turn the handwheel to the right, right turn signal flashes slowly; When gearbox is shifted
to forward gear, the headlights enter into their high-luminance state; When brake is applied/gearbox is shifted to reverse gear, the tail lights enter into their low-
luminance state; Press CH4, the emergency lights flash slowly.
•
Breathing mode: All lights (including roof lights and ambient lights) breathe and flash; Set CH3 to its rightmost position to turn on all car lights, and set CH3 to its
leftmost position to turn off all car lights.
•
Sharp flash mode: All lights (including roof lights and ambient lights) flash; Set CH3 to its rightmost position to turn on all car lights, and set CH3 to its leftmost position
to turn off all car lights.
•
Switch Method: Quickly press CH4 twice to switch the modes.
•
The above method is intended for using CH3 to control lighting/width light or emergency light. Please refer to 2 for details on handwheel control.
3. Working modes of ambient light and roof light:
•
Ambient light and roof light include two working modes: single mode and combined mode, which can be adjusted and used in normal mode and sports mode, but
can not be used in breathing mode and flash mode; In the separate mode, the ambient light and the roof light are independently controlled and do not interfere with
each other; In the combined mode, the ambient light and the roof light work together and can be controlled uniformly. The two working modes can be switched
when the handwheel is turned clockwise to its maximum stroke four times.
•
The combined mode includes three working modes: quick flashing, breathing and OFF. Different flashing modes can be switched when the handwheel is turned
clockwise to its maximum stroke three times.
•
In the single mode, the ambient light has four working modes: breathing, sharp flashing, three quick flashing one long lighting-off and OFF. Different modes can be
switched when the handwheel is turned clockwise to its maximum stroke three times; The roof light has three working modes: always on, slowly flashing, and OFF,
and it can be switched to different modes when the handwheel is turned counterclockwise to its maximum stroke three times.
Notes:
(1) If the front and tail lights are contrary to the actual control, the control mode of the front and tail lights should be reversed. When the transmitter is turned on,
turn and keep the hand wheel counterclockwise to its maximum stroke, and power on the receiver to conduct the switchover; If the left and right turn signals are
contrary to the actual control, it is only necessary to exchange the left and right light wires at the car light interface.
(2) If CH1 is set with channel reversal, all the above handwheel operations should be operated in the reverse direction (change clock wise for counterclockwise, and
change counterclockwise for clockwise).
(3) The direction CH1 and accelerator CH2 for car light control are capable of automatic neutral position identifying.
电调功能使用说明
ESC function instructions
1. 连接相关设备 :
•
连接前请确认电调开关处于关闭（OFF）状态，将电机与电调的 M+/M- 相连接，舵机接到电调 3Pin 排针接口上（"-""+""S " 相对应），电池与电调输入正负
极对应相接。
电调保护功能
ESC protection
