FS-R4A
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
产品型号：FS-R4A
适配发射机：FS-MG41
适合机种：车
通道个数：4
车灯接口数：6
无线频率：2.4GHz ISM
无线协议：ANT（蚂蚁版自动调频数字系统）
天线类型：单天线
输入电源：Lipo（2S）/NiMH(5~7Cell)
BEC 输出：6V/1A
持续 / 峰值电流：10A/50A
数据输出：PWM
温度范围：-10℃—+60℃
湿度范围：20%~95％
防水等级：PPX4
在线更新：无
外形尺寸：33mm*29mm*14mm
机身重量：12.7g
认证： CE，FCC ID:N4ZR4A00
FS-R4A 采用 ANT 协议，是一款电调、LED 灯组控制板三合一接
收机，外置单天线，可输出 PWM 信号和车灯控制信号 , 能够实
现双向传输，采用自动对码，设计小巧紧凑，可适配多种车型使用。
FS-R4A based on ANT protocol is a three-in-one receiver with ESC and LED light group control
board. It has an external single antenna, can output PWM signal and light control signal, can
implement two-way transmission, adopts automatic binding, and has a compact design, which
can be adapted to various models.
产品介绍
Introduction
接收机概览
Receiver overview
产品规格
Product specification
[1] CH1 通道接口
[2] CH3 通道接口
[3] CH4 通道接口
[4] 左转灯接口
[5] 右转灯接口
[6] 前大灯接口
[7] 后尾灯接口
[8] 氛围灯接口
[9] 车顶灯接口
[10] 车灯接口“-”端
[11] 车灯接口“+”端
[12] 接收机天线
[13] LED 指示灯
[14] 电池线“-”
[15] 电池线“+”
[16] 马达线 “M-”
[17] 马达线 “M+”
[18] 电源开关线
Product Name: FS-R4A
Adaptive transmitter: FS-MG41
Model Type: Car
Channels: 4
Numbers ofLight Interfaces：6
RF: 2.4GHz ISM
2.4G Protocol: ANT
Antenna: Single Antenna
Input Power: Lipo（2S）/NiMH(5~7Cell)
BEC Output: 6V/1A
Continuous / Peak Current：10A/50A
Data Output: PWM
Temperature Range: -10℃—+60℃
Humidity Limit: 20%~95%
WaterProof: PPX4
Online Update: No
Dimensions: 33mm*29mm*14mm
Weight: 12.7g
Certification: CE，FCC ID:N4ZR4A00
对码
Binding
本款接收机上电即自动进入对码状态。
将发射机按住对码键开机进入对码状态，此时 G.LED 快闪，松开“BIND”键；
1. 接收机上电等待 1 秒没有连接将自动进入对码；
2. 对码成功后 , 接收机 LED 指示灯常亮；
注：（1）对码时请先将发射机进入对码状态，再将接收机进入对码状态，若 10s 内对码没有完成，接收机指示灯进入慢闪状态；
（2）如果重新对码成功，车灯的所有设置将恢复默认值。
The receiver automatically enters the binding state once it is powered on.
1. Press the BIND key to turn on the transmitter and allow it to enter its binding state. Here, G.LED flashes quickly, and operator releases the BIND key.
2. When the receiver is powered on and waits for 1 second, it will automatically enter the binding state if it is not connected;
3. After the binding is successful, the LED indicator of the receiver is always on.
Notes: (1) Set the transmitter to its binding state first, and then set the receiver to its binding state. If the binding is not completedwithin 10s, the indicator
light of the receiver will enter its slow flashing state.
(2) If re-binding is successful, all the settings of the car lights will be restored to their default values.
[1] CH1
[2] CH3
[3] CH4
[4] Left Light port
[5] Right Light port
[6]Head Light port
[7]Tail Light port
[8] Ambient Light port
[9]Roof Light
[10]Light port“-”
[11]Light port“+”
[12]Antenna
[13] LED
[14]Battery line“-”
[15]Battery line“+”
[16]Motor line“M-”
[17] Motor line “M+”
[18]Power switch line
[19] Stickers
[20]Channel port “S ”
[21]Channel port“+”
[22]Channel port“-”
电调保护功能
ESC protection
[19] 贴纸
[20] 通道接口 “S ”端
[21] 通道接口“+”端
[22] 通道接口“-”端
本款接收机具有上电自检显示、过热报警提示、电压过低 / 高报警提示等多种提示功能。
•
自检显示：接收机上电瞬间所有车灯长亮 1S；
•
过热报警：检测到电调内部温度超过 110℃时，马达无输出，所有车灯快闪提示；当温度低于 70℃时恢复正常输出。
•
电压过低 / 高报警：接收机进入电压过低保护时，马达无输出，所有车灯慢闪提示； 接收机进入电压过高保护时，所有通道无输出，所有车灯快闪提示。
This receiver's have multiple prompt functions such as power-on self-check display, overheating alarm prompt, and low/high voltage alarm prompt.
•
Self-check display: all car lights will be on for 1S when the receiver is powered on;
•
Overheating alarm: When the internal temperature of the ESC is detected to exceed 110℃ ,motor has no output, all car lights flash promptly, and the normal
output will be restored when the temperature is lower than 70℃ ；
