接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021Flysky Technology co., ltd
FS-A8S
FS-A8S 是一款专用于穿越机的单向接收机，采用了 AFHDS
2A（第二代增强版自动跳频数字系统）。它体积小巧便于
安装，可输出标准 PPM 信号和 18 个通道的 i-BUS 信号以
及 16 通道的 S.BUS 信号。
The FS-A8S is a compact 1-way receiver designed for Drone
aircraft. It uses the AFHDS 2A (Automatic Frequency Hopping
Digital System) protocol, supports standard PPM output and has
i-BUS support for up to 18 channels.It also has S.BUS support for
up to 16 channels.
产品介绍
Introduction
接收机概览
Receiver overview
用于连接接收机与模型的各个部件。
PPM 信号接口： 输出标准的 PPM 信号；
i-BUS/S.BUS 信号接口 : 用于输出 i-BUS/S.BUS 信号。
注：接收机将 RSSI 数据转换成 CH14 通道值通过 i-BUS/S.BUS 输出给
飞控，信号强度为 0 时对应通道值为 1000，信号强度为 100 时对应通
道值为 2000，线性对应相关。
These ports are for connecting the receiver to various models and
flight controllers.
PPM signal port: Outputs standard PPM signal.
i-BUS/S.BUS signal port: Outputs i-BUS/S.BUS signal.
Note: The receiver uses CH14 for output of RSSI data to the
onboard flight controller via i-BUS/S.BUS. The receiver signal
strength data from the onboard flight controller will be displayed
as values between 0 and 100 (100 being max signal strength) and
the corresponding values displayed on CH14 on the transmitter
will be 1000 and 2000 (2000 being max signal strength).
产品规格
Product specification
产品型号：FS-A8S
适用机型：穿越机
无线频率：2.4GHz
无线协议：AFHDS 2A
天线类型：单天线
输入电源：4.0 ～ 8.4V
数据输出：PPM/ i-BUS/S.BUS
温度范围：-15℃—+60℃
湿度范围：20%-95%
在线更新：无
外形尺寸：20mm*14mm*5.3mm
机身重量：1.2g
安规认证：CE，FCC
Product Name: FS-A8S
Model Type : Multi-rotor
RF: 2.4GHz
Protocol: AFHDS 2A
Antenna: Single Antenna
Input Power: 4.0-8.4V
Data Output: PPM/i-BUS/S.BUS
Temperature Range: -15℃—+60℃
Humidity Limit: 20%-95%
Online Update: no
Dimensions: 20mm*14mm*5.3mm
Weight: 1.2g
Certification: CE，FCC
对码
Binding
1. 将发射机进入对码状态；（发射机进入对码状态的方式可能不同，请根据发射 机的使用说明书进行操作）
2. 按住接收机上的对码按键，并为接收机连接电源。接收机上的指示灯快闪表示接收机进入对码状态；对码成功后，接
收机状态指示灯由快速闪烁变为慢速闪烁。
3. 将发射机手动退出对码界面，此时接收机状态指示灯变为常亮。
4. 检查发射机、接收机、模型是否正常工作。如有异常，重复以上步骤重新对码。
1. For information on putting the transmitter into bind mode please refer to the transmitters user manual.
2. Power on the receiver while holding the bind button. If the receiver's LED is flashing this means it has entered bind
mode.
If binding is successful the receiver's LED will begin to flash slower.
3. On the transmitter, manually exit the binding menu. Once you have exited the bind menu the receiver's LED will stop
flashing and remain solid.
4. Check to make sure the model and receiver work as expected. If anything does not work as correctly, restart this
