FGr12B
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2020 Flysky Technology co., ltd
1. Press and hold the receiver BIND button [16] while powering on the receiver, release the BIND button after receiver is powered on, the
LED [14] on the receiver will flash rapidly;
2. Put the transmitter into bind mode;
3. The binding process is complete when the LED on the receiver stops flashing and is on continuously.
• If a transmitter that has had its radio frequency (RF Standard) set to “AFHDS3 1 way” (please refer to your transmitter user manual)
enters bind mode, the receiver LED will instead flash slowly. Exit bind mode on the transmitter and if the receiver LED stops flashing
and is on continuously, the binding process is complete
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems
arise.
对码
Binding
发射机在更新完后，如无法与接收机对码，需强制更新接收机。
1. 接收机按下对码按键，上电十秒钟后指示灯三闪一灭，松
开对码按键；
2. 在发射机端选择接收机更新并进入更新状态；
3. 更新完成指示灯慢闪。
强制更新
Forced update
失控保护功能用于在接收机失去信号不受控制后，保护模型及人员
安全。
• 若发射机未设置失控保护通道值输出，接收机在进入失控保
护状态后将维持失控前输出；若发射机设置了失控保护，则
按照发射机通道设置输出。
失控保护
Failsafe
兼容性
Compatibility
该接收机兼容所有 AFHDS3 的发射机和高频头。（主要包括 PL18、
NB4、NB4 Lite、 FRM302 等）
注意事项：
• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者引
擎继续工作而引发事故。
• 确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有 1 厘米以上的
距离。
Attention:
• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation
or loss of control.
• Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical
noise.
• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
If after a firmware update is performed and the transmitter is unable
to bind to the receiver, the receiver may need to be put into forced update
times.
1. Power on the receiver while pressing the BIND button [16] for
then approximately ten seconds until the LED [14] flashes three
times,release the BIND button.
2. Go to the RX Setup menu on your transmitter and select “RX
Update”.
3. When the receiver LED flashes slowly, the update is successful.
This function protects your vehicle by preventing unexpected
behaviors in case of signal lost.
• Users should always input Fail Safe parameters before operating
their vehicles. If the Fail Safe function has not been set on the
transmitter and signal lost occurs, the receiver will continue
to operate and maintain all output value at the last received
instructions from the transmitter. If the Fail Safe parameters
on the transmitter has set been set, the receiver will set output
values according to user parameters during signal lost.
The FGr12B receiver is compatible with all AFHDS 3 transmitters
and RF modules (including PL18, NB4, NB4 Lite, FRM302 etc.)
