IMPORTANT!
v
Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely
(contact the FLYMO Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the blade to stop, remove the battery, remove
the safety key and use gloves before you troubleshoot the
product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v
Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v
Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from
the FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300 Li: Art. FLY 069
• FLYMO replacement blade for 340 Li: Art. FLY 087
SimpliStore 300 Li [ Fig. T2 ]:
1. Ensure the lawnmower is stopped and disconnected. Insert a screw-
driver through the reinforced hole on the deck into the drive pulley
wheel to stop the wheel from turning during the blade change.
2. Unscrew the blade bolt. Take care not to damage the drive pulley wheel
when applying force.
3. Remove the blade bolt and the washer.
4. Remove the blade.
5. Put the new blade on the lawnmower.
6. Put the washer and the blade bolt on the lawnmower.
7. Screw the new blade tight with the blade bolt. Tightening torque is
15 – 20 Nm. Do not over-torque.
Take care not to damage the drive pulley wheel when applying force.
8. Ensure the screwdriver is removed before attempting to turn on the
machine.
SimpliStore 340 Li [ Fig. T3 ]:
1. Ensure the lawnmower is stopped and disconnected. Insert a screw-
driver through one of the holes in the spacer into the reinforced hole on
the deck to stop the axle from turning.
2. Unscrew the blade bolt. Take care not to damage the spacer when
applying force.
3. Remove the blade bolt and the washer.
4. Remove the blade.
5. Put the new blade on the lawnmower.
6. Put the washer and the blade bolt on the lawnmower.
7. Screw the new blade tight with the blade bolt. Tightening torque is
15 – 20 Nm. Do not over-torque.
Take care not to damage the spacer when applying force.
8. Ensure the screwdriver is removed before attempting to turn on the
machine.
Problem
Possible Cause
Remedy
Mower does not start
Safety key is not in position
I
.
v
Turn the safety key to
position
I
.
Battery is not put completely
into the battery holder.
v
Put the battery completely
into the battery holder until
it audibly engages.
Problem
Possible Cause
Remedy
Mower does not start
Battery is empty.
v
Charge the battery.
Motor is blocked.
v
Remove the obstacle.
Start again.
Engine is jammed and
makes a noise
Motor is blocked.
v
Remove the obstacle.
Start again.
Cutting height is too low.
v
Raise the cutting height.
Loud noises, the mower
is rattling
Screws on engine, its fixing
or on the mower chasing are
loose.
v
Let the screws be tightened
by an authorised specialist
dealer or the FLYMO Service.
Mower runs unevenly or
vibrates strongly
Blade is damaged / worn or the
blade mounting is released.
v
Replace the blade.
Blade is very dirty.
v
Clean the blade.
Lawn is not cleanly mowed
Blade is blunt or damaged.
v
Replace the blade.
Cutting height is too low.
v
Raise the cutting height.
Red Error-LED on the battery
illuminates
Battery temperature is out
of range.
v
Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
After pushing the button
no LED on the battery
illuminates
Battery is defective.
v
Replace the battery.
After pushing the button
the LED on the battery
flashes red.
Battery temperature is out
of range.
v
Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
Charging control lamp
on the charger does not
illuminate
Battery charger or charging
cable are not connected
correctly.
v
Connect the battery charger
and charging cable correctly.
Charging control lamp on
the charger illuminates red
Battery temperature is out
of range.
v
Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
Charging control lamp on
the charger flashes red
Battery error / battery defective.
v
If the battery cannot be
reset by connecting it to
the charger, contact the
FLYMO Service.
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers
approved by FLYMO.
7. TECHNICAL DATA
Battery Lawnmower
Unit
Value
SimpliStore 300 Li
9705395-xx
Value
SimpliStore 340 Li
9705396-xx
Speed of rotation cutting
blade
R/min
3500
3300
Cutting width
cm
30
34
Cutting height adjustment
mm
25 – 65
(3 positions)
20 – 60
(5 positions)
Volume of grass box
l
30
35
Weight (without Battery)
kg
8.0
10.4
Sound pressure level L
pA
1)
Uncertainty k
pA
dB (A)
88.4
3.0
82.7
3.0
Sound power level L
WA
2)
:
measured / guaranteed
Uncertainty k
WA
dB (A)
88 / 89
1.0
86 / 87
1.0
Hand / arm vibration a
vhw
1)
m/s
2
< 2.5
< 2.5
Measuring process complying with:
1)
EN 60335-2-77
2)
RL 2000/14/EC
/ S.I. 2001 No.1701
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
Battery B16-2025A
Unit
Value (Art. 967913201)
Battery voltage
V (DC)
20
Battery capacity
Ah
2,5
Number of cells (Li-Ion)
5
Battery charging time
(approx.)
min.
120
Lawn area per battery
charge (approx.)
m
2
250
Appropriate FLYMO System Batteries B16-2025A: Art. 967913201
7
22301-85.960.01.indd 7
22301-85.960.01.indd 7
25.10.21 14:12
25.10.21 14:12
