Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v
Dispose of the product through or via your municipal recycling
collection centre.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v
Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v
Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300R: Art. FLY 085
• FLYMO replacement blade for 340R: Art. FLY 086
• FLYMO replacement blade for 380R: Art. FLY 088
1. Unscrew the blade bolt.
2. Remove the blade bolt and the washer.
3. Remove the blade and the spacer.
4. Put the spacer and the new blade on the mower.
5. Put the washer on the blade bolt.
6. Screw the new blade tight with the blade bolt
(tightening torque is 15 – 20 Nm).
Problem
Possible Cause
Remedy
Mower does not start
Mains cable is disconnected
or damaged.
v
Connect the mains cable or
if necessary let it be replaced
by an authorised specialist
dealer or the FLYMO Service.
Motor is blocked.
v
Remove the obstacle.
Start again.
Engine is jammed and
makes a noise
Motor is blocked.
v
Remove the obstacle.
Start again.
Cutting height is too low.
v
Raise the cutting height.
Loud noises, the mower
is rattling
Screws on engine, its fixing
or on the mower chasing are
loose.
v
Let the screws be tightened
by an authorised specialist
dealer or the FLYMO Service.
Mower runs unevenly or
vibrates strongly
Blade is damaged / worn or the
blade mounting is released.
v
Replace the blade.
Blade is very dirty.
v
Clean the blade.
Lawn is not cleanly mowed
Blade is blunt or damaged.
v
Replace the blade.
Cutting height is too low.
v
Raise the cutting height.
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers
approved by FLYMO.
7. TECHNICAL DATA
Electric Lawnmower
Unit
Value
EasiMow 300R
Value
EasiMow 340R
Value
EasiMow 380R
Rated power
W
1000
1400 1600
Mains voltage
V (AC)
230
230
230
Mains frequency
Hz
50
50 50
To start:
The mower is fitted with a two-handed safety device (start lever
with starting lockout) to prevent the mower from being turned on
by accident.
There are two start levers. Either one has to be used to start.
1. Push the starting lockout with one hand and pull the start lever
with the other hand.
The mower starts.
2. Release the starting lockout.
Only for 340R / 380R [ Fig. O9 ]: The level indicator opens during
mowing. When it closes during mowing, the grass box is full and
must be emptied.
To stop:
v
Release the start lever.
The mower stops.
Tips to use the mower:
If grass residue is left in the discharge opening, pull the mower backwards
about 1 m so that the grass residue can drop out downwards.
To produce a well-maintained lawn and optimise the cutting performance,
we recommend to cut the lawn regularly once a week if possible. The lawn
becomes denser if you cut it frequently.
After relatively long cutting intervals (holiday lawn), first of all cut in one
direction with the highest cutting height and then cut in the crosswise
direction with the required cutting height.
If possible, only cut the grass when it is dry, if the grass is damp, the
cutting pattern will be uneven.
Rear Roller:
For lawnmowers fitted with a rear roller, it is possible to create a striped
effect on the lawn. For the best stripe results, we recommend cutting on
the lowest possible cutting height suited to your lawn. The stripe effect will
fade in time between cuts.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v
Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v
Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v
Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside, the blade and the discharge opening with
a brush (do not use sharp objects).
To clean the overside of the mower and the grass box:
1. Clean the overside with a damp cloth.
2. Clean the airflow slots and the grass box with a soft brush
(do not use sharp objects).
5. STORAGE
To put into storage [ Fig. S1 ]
The product must be stored away from children.
1. Disconnect the mower from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Wrap the cable around the cable hooks.
4. Store the mower in a dry, enclosed and frost-free place.
6
