background image

                                                                                                                                                                                         12 

 

 

Add one pair of weights at a time and repeat the "horizontal to vertical" test until it falls at 

the correct rate. It will probably not be perfect. 

 

 

You'll get one that's too slow and then you'll add a pair and it will fall too fast. When that 

happens, take off the last pair of weights that you added. 

 

 

Tighten down the weights so they don't slide around. 

 

To  get  the  count  perfect,  slightly  lower  the  center  post  that  attaches  the  base  platform 

with  the  weights  until  you  get  the  "one-one  thousand,  two  one  thousand"  count  to  the 

vertical position. 

 

 

Fine-tune  the  left-right,  forward-backward  balance.  You  will  have  to  go  back  and  forth     

between the two directions to get the balance just right. Loosen the screw sets that allow 

the sled to move left and right. Adjust the top plate so that it is centered and tighten down 

the screws like you would a tire slowly and alternating side to side. 

 

 

Repeat for "forward-backward" balancing. 

 

 

Check to see if your camera is sitting level. If not, repeat the necessary steps until it does. 

 

 

Practice walking/movements ensuring your body motion is not transmitted to your hands 

and then the flycam and camera.

 

When handling your junior one hand holds  onto the handle while  the other is used to gently 
guide the camera in the direction you wish to shoot and frame the shot.  

 

For normal shooting, hold the handle in the middle.  
For shots that require framing the camera up, down or sideways, hold the handle firmly at the 
bottom.  

 

This will allow the “yoke” part of the gimbal to rotate without hitting your hand or knuckles. 

HOLDING FLYCAM JUNIOR 

Summary of Contents for FLCM-JR















Reviews: