manualshive.com logo in svg

Flybox Fuel L-P, Installation And User Manual, Safety Instructions And Warning Booklet, Page: 59 / 68

Share
Download
Flybox Fuel L-P Installation And User Manual, Safety Instructions And Warning Booklet Download Page 59

FLYBOX

Omnia57 

Fuel L-P

- 

Installation and User Manual,

Safety Instructions and Warning Booklet

Rev. 1.0

®

48

Operating Instructions

When switched-ON, the display will immediately show the
main page with the enabled gauges.

NOTE

:  The  first  time  you  switch-ON  the 

Omnia57  F-P

,

there will not be enabled tanks. You need to enable and
calibrate the tanks as explained in chapter 

4.4.3

.

The fuel pressure gauge will not be enabled too, so if you
have  the  fuel  pressure  sensor  installed,  enable  it  as
explained in the chapter 

4.5

.

The example below refers to the installation comprising of
four tanks and the fuel pressure gauge; if your aircraft has
less  than  4  tanks,  the  indication  of  the  display  might  be
different. The tanks are named:

L

 (left), 

M

 (main), 

A

 (auxiliary), 

R

 (right).

5.3 USE OF THE INSTRUMENT

Summary of Contents for Fuel L-P





































































Reviews:

No comments