FS-R4D
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2020 Flysky Technology co., ltd
车灯控制
Car lamp control
车灯控制主要是通过发射机的的设置实现车灯亮灯状态及亮灯模式的转换。
1. 车灯的四种闪烁状态：
• 慢闪：车灯呈现缓慢闪烁的状态；
• 爆闪：车灯呈现快速闪烁的状态；
• 呼吸灯：车灯呈现由暗变亮，然后又由亮变暗的闪烁状态；
• 低亮：车灯呈现亮度为常亮亮度的 50% 左右的闪烁状态。
2. 车灯工作的四种模式状态：
• 普通模式:打左转向，左转向灯慢闪；打右转向，右转向灯慢闪；CH3最左，所有车灯熄灭，CH3在中位或者最右，前灯常亮，后灯低亮；
后退 / 刹车，后灯常亮，按下 CH4 按键，左灯右灯慢闪，再次按下 CH4 按键取消闪烁；
• 运动模式 : 打左转向，左转向灯慢闪；打右转向，右转向灯慢闪；油门加速，前灯常亮，油门刹车或后退，后灯常亮，按下 CH4 按键，
左灯右灯慢闪，再次按下 CH4 按键取消闪烁。
• 呼吸模式：CH3 在中位或者最右，左灯、右灯、前灯和后灯一起呈呼吸灯闪烁状态；
• 爆闪模式：CH3 在中位或者最右，左灯、右灯、前灯和后灯一起呈快闪闪烁状态。
3. 车灯的模式切换：
• 接收机上电建立连接第一时间将发射机 CH1 顺时针转至最高位并保持，CH2 保持在中位状态，接收机每上电一次切换一个模式；
• 四种模式循环切换，断电后保存断电前的模式状态，默认模式为普通模式；
• 前进、后退 / 刹车受 CH2 通道值控制，控制方式可切换正反向；
• 正反向循环切换，掉电保存，默认为正向；
• 车灯模式及正反向设置，接收机对码操作成功后恢复默认状态。
注：
• 以上 CH1、CH2、CH3、CH4 均为发射机的通道，其中 CH4 通道主要控制应急灯的闪烁情况；
• 以上操作均为 CH1、CH2 未开启方向倒置开关下进行的操作，如若开启方向倒置开关，则之前的发射机操作方式需进行相反方向
的操作调整。
• 方向 CH1 和油门 CH2 可自动识别中位，即上电时检测到 CH1、CH2 的通道值在中位附近时，则将自动检测到的通道值当做控制车
灯的中位值。
Car lamp control: to switch among the lighting states and the lighting modes by setting of the transmitter.
1. Four flashing states of the car lamp:
• Slow flashing: the car lamps are in a state of slow flashing;
• Sharp-flashing: The car lamps are in a state of quick flashing;
• Breathing lamp: The flashing car lamp light becomes brighter and brighter and then darker and darker gradually;
• Low brightness: The brightness of the flashing car lamp light is about 50% of the constant brightness.
2. Four mode states of car lamps:
• Normal mode: Turn left and the left turn signal flashes slowly; turn right and the right turn signal flashes slowly; when CH3 is
in the leftmost position, all lamps go out; when CH3 is in the neutral or rightmost position, the headlamps are constantly on,
and the rear lamps are set to low brightness; during reversing/braking, the rear lamps are constantly on; press CH4 button,
the left and right lamps flash slowly; press CH4 button again to cancel flashing;
• Sports mode: Turn left and the left turn signal flashes slowly; turn right and the right turn signal flashes slowly; during
throttle acceleration, headlamps are constantly on; during throttle braking or reversing, rear lamps are constantly on; press
CH4 button, left and right lamps flash slowly; press CH4 button again to cancel flashing.
对码
Binding
The receiver will automatically enter the binding state when it is powered on.
• Turn on the transmitter and allow it to enter the binding state;
• Power on the receiver. The indicator light flashes slowly, indicating the completion of binding;
• Restart the transmitter. The indicator light of the receiver is constantly on, indicating that normal communication can start.
• Check to make sure the transmitter and receiver functions are working correctly, repeat steps above if any problems arise.
Tips：
1. The receiver will automatically enter the binding state under abnormal communication. If the receiver and transmitter have completed
binding, please start the transmitter before the receiver is started, thus avoiding the inconvenience caused by the receiver's automatic
entry into the binding state.
2. If a transmitter that has finished binding is not turned on before the receiver or the receiver is not bound, the receiver will automatically
enter the binding state after being powered on, and the indicator light of the receiver will flash quickly.If the receiver and transmitter fail
to complete binding within 10s, the receiver will automatically exit the binding state, and the indicator light will flash slowly, waiting for
the transmitter which has completed the binding to start up and enter the normal communication state; if the receiver and transmitter
complete binding within 10s, the indicator light of the receiver flashes slowly, the transmitter is restarted, and the indicator light of the
receiver is constantly on, indicating successful binding.