Fluo FSS 241 EI/JDF-N3 User Manual Download Page 19

Page: 19 / 33

Error Code

When air conditioner status is abnormal, temperature indicator on indoor unit will blink to

dispiay corresponding error code. Please refer to below list for identification of error code.

Below listed error codes are only part error codes. Please refero to error code list in serive
manual for more information.

If there're other error codes, please contact qualified professionals for service.

Malfunction analysis

Error

code

Troubleshooting

Solution

Filter filth blockage alert

Power off,clean filter.If the filter is not dirtey, turn off

the air conditioner for 2s then restart,the code will be

removed automatically.

Overheat protection

Turn off,restart after 5min,if the code occurs again after

a few minutes, please contact the professional person.

Overcurrent protection Turn off,restart after 5min,if the code occurs again after

a few minutes, please contact the professional person.

Auxiliary heat control

circuit malfunction

Pull out the plug, please contact the professional

person.

Jumper malfunction

Pull out the plug, restart after 10s, if the code occurs

again , please contact the professional person.

PG motor(indoor)zero-

crossing detecting circuit

malfunction

Turn off,restart after a few seconds, if the code

occurs again after a few minutes, please contact the

professional person.

No feedback signal of

indoor unit fan

Turn off,restart after a few seconds, if the code

occurs again after a few minutes, please contact the

professional person.

L3/L6

Communication

malfunction

Power off the unit, restart after 10s, if the code occurs

again ,please check the communication wire of indoor

unit and outdoor unit is correct of not, then power on

again.

Short/open circuit of indoor

environment sensor

Power off the unit, restart after 10s, if the code occurs

again , please contact the professional person.

U1 Short/open circuit of indoor

unit tube sensor

Power off the unit, restart after 10s, if the code occurs

again , please contact the professional person.

Liquid pipe temp. sensor

malfunction

Power off the unit, restart after 10s, if the code occurs

again , please contact the professional person.

Gas pipe temp. sensor

malfunction

Power off the unit, restart after 10s, if the code occurs

again , please contact the professional person.

Mode conflict

The mode of this indoor unit is conflicting with other

indoor units, please turn off other indoor units or

change the mode to non-conflicted mode.

Summary of Contents for FSS 241 EI/JDF-N3


































Search results

Summary of Contents for FSS 241 EI/JDF-N3

Reviews:

Related manuals for FSS 241 EI/JDF-N3

Brands by name

Popular brands

Fluo FSS 241 EI/JDF-N3, User Manual

Search results

Summary of Contents for FSS 241 EI/JDF-N3

Reviews:

Related manuals for FSS 241 EI/JDF-N3

Brands by name

Popular brands