manualshive.com logo in svg

Fluke TS53 PRO, User Manual, Page: 34 / 38

Share
Download
Fluke TS53 PRO User Manual Download Page 34

30

TS54TDR/TS53 PRO Test Sets
Users Guide

GOL07.EPS

Figure 6. How to Replace the Battery

Replacing the Belt Clip

You can replace the belt clip if it is damaged. To order a 
replacement belt clip, contact your local Fluke 
Networks authorized distributor.

To replace the belt clip:

Refer to Figure 7.

1

Use a Phillips screwdriver to remove the two 
screws that attach the belt clip to the test set. 
Remove the belt clip.

2

Put the screws into the plate on the new belt clip.

3

Put the end of the plate into the slot as shown in 
Figure 7 before you align the screws with the holes 
in the test set.

4

Tighten the screws.

Caution

Do not over-tighten the screws for the belt 
clip. If you do, you can cause damage to the 
screw holes.

GOL06.EPS

Figure 7. How to Remove and Install the Belt Clip

Replacing the Belt Clip Protector

The belt clip protector prevents damage to the belt clip 
if you drop the test set. You can replace the protector if 
it is damaged:

1

Remove the belt clip as described in the previous 
section.

2

Remove and install the protector as shown in 
Figure 8.

GOL09.EPS

Figure 8. How to Remove and Install 

the Belt Clip Protector

Summary of Contents for TS53 PRO







































Reviews:

No comments