Fluke PQ Window Instructions Manual Download Page 4

Symbols

Symbol

Description

W

WARNING. RISK OF DANGER.

X

WARNING. HAZARDOUS VOLTAGE. Risk of 
electric shock.

Consult user documentation.

Measurement Category III is applicable to test and 
measuring circuits connected to the distribution 
part of the building’s low-voltage MAINS 
installation.

Measurement Category IV is applicable to test and 
measuring circuits connected at the source of the 
building’s low-voltage MAINS installation.

P

Conforms to European Union directives.

)

Certified by CSA Group to North American safety 
standards.

Conforms to relevant Australian EMC standards.

Type 1

NEMA 250 Enclosure Type. Enclosure suitable for 
indoor use under normal atmospheric conditions. 
Protection against access to hazardous parts and 
ingress of solid foreign objects (falling dirt).

Type 12

NEMA 250 Enclosure Type. Enclosure suitable for 
indoor use. Protection against dust, dripping, and 
light splashing of non-corrosive liquids.

~

This product complies with the WEEE Directive 
marking requirements. The affixed label indicates 
that you must not discard this electrical/electronic 
product in domestic household waste. Product 
Category: With reference to the equipment types in 
the WEEE Directive Annex I, this product is 
classed as category 9 "Monitoring and Control 
Instrumentation" product. Do not dispose of this 
product as unsorted municipal waste.

Summary of Contents for PQ Window

















Reviews: