background image

7

Digital Communication Interface

The furnace calibrator is capable of communicating with and being controlled
by other equipment through the digital interface. Two types of digital interface
are available — the RS-232 serial interface and the optional IEEE-488 GPIB
interface.

With a digital interface the instrument may be connected to a computer or other
equipment. This allows the user to set the set-point temperature, monitor the
temperature, and access any of the other controller functions, all using remote
communications equipment.

7.1

Serial Communications

The calibrator may be installed with an RS-232 serial interface that allows se-
rial digital communications over fairly long distances. With the serial interface
the user may access any of the functions, parameters and settings discussed in
Section with the exception of the baud rate setting.

7.1.1

Wiring

The serial communications ca-
ble attaches to the calibrator
through the DB-9 connector at
the back of the instrument. Fig-
ure shows the pin-out of this
connector and suggested cable
wiring. To eliminate noise, the
serial cable should be shielded
with low resistance between
the connector (DB-9) and the
shield.

7.1.2

Setup

Before operating the serial in-
terface, set up the BAUD rate
and other configuration param-
eters. These parameters are
programmed within the serial
interface menu.

To enter the serial parameter
programming mode first press
“EXIT” while pressing “SET”
and release to enter the second-
ary menu. Press “SET” repeat-
edly until the display reads

39

7 Digital Communication Interface

Serial Communications

Figure 8.

Serial Cable Wiring

Summary of Contents for 9116A

















































































Reviews: